AASHTO T 315 : 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
METHOD OF TEST FOR DETERMINING THE RHEOLOGICAL PROPERTIES OF ASPHALT BINDER USING A DYNAMIC SHEAR RHEOMETER (DSR)
Hardcopy , PDF
28-12-2022
English
01-01-2012
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCED DOCUMENTS
3. TERMINOLOGY
4. SUMMARY OF TEST METHOD
5. SIGNIFICANCE AND USE
6. APPARATUS
7. HAZARDS
8. PREPARATION OF APPARATUS
9. VERIFICATION AND CALIBRATION
10. PREPARING SAMPLES AND TEST SPECIMENS
11. PROCEDURE
12. INTERPRETATION OF RESULTS
13. REPORT
14. PRECISION AND BIAS
15. KEYWORDS
APPENDIXES (Nonmandatory Information)
X1. TESTING FOR LINEARITY
X2. CONTROL CHART
X3. EXAMPLE
X4. USE OF REFERENCE FLUID
X5. CAUTIONS IN USING REFERENCE FLUID
X6. CALCULATION OF G* FROM STEADY-STATE VISCOSITY
MEASUREMENTS
X7. METHODS FOR TRANSFERRING THE FLUID TO THE TEST PLATES
X8. SELECTION OF GAP CLOSURE TO OBTAIN BULGE
X9. RECOMMENDED GAP CLOSURE VALUES
X10. FACTORS AFFECTING BULGE DEVELOPMENT
X11. DETERMINATION OF TIME TO THERMAL EQUILIBRIUM
X12. METHOD TO DETERMINE THE TIME REQUIRED TO OBTAIN
THERMAL EQUILIBRIUM
X13. SAMPLE REPORT
X14. REFERENCES
Gives the determination of the dynamic shear modulus and phase angle of asphalt binder when tested in dynamic (oscillatory) shear using parallel plate test geometry.
| DevelopmentNote |
Included in AASHTO HM. (10/2013)
|
| DocumentType |
Standard
|
| Pages |
33
|
| PublisherName |
American Association of State Highway and Transportation Officials
|
| Status |
Superseded
|
| SupersededBy |
| AASHTO TP 101 : 2012 | METHOD OF TEST FOR ESTIMATING FATIGUE RESISTANCE OF ASPHALT BINDERS USING THE LINEAR AMPLITUDE SWEEP |
| AASHTO T 350 : 2014 | METHOD OF TEST FOR MULTIPLE STRESS CREEP RECOVERY (MSCR) TEST OF ASPHALT BINDER USING A DYNAMIC SHEAR RHEOMETER (DSR) |
| AASHTO R 15 : 2000 : R2012 | PRACTICE FOR ASPHALT ADDITIVES AND MODIFIERS |
| ASTM D 7175 : 2015 : REDLINE | Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer |
| AASHTO TP 70 : 0 | METHOD OF TEST FOR MULTIPLE STRESS CREEP RECOVERY (MSCR) TEST OF ASPHALT BINDER USING A DYNAMIC SHEAR RHEOMETER (DSR) |
| AASHTO TP 126 : 2017 | METHOD OF TEST FOR EVALUATION OF THE TRACKING RESISTANCE OF HOT-POURED ASPHALT CRACK SEALANT BY DYNAMIC SHEAR RHEOMETER (DSR) |
| DVGW G 440-B1 Merkblatt 9:2018 | Explosion protection document for plants and systems for public gas supply; 1. Supplement: Amendment of the example for Gas-Pressure-Regulating and Measuring Stations |
| AASHTO M 320:2010 | SPECIFICATION FOR PERFORMANCE-GRADED ASPHALT BINDER |
| AASHTO M 320 : 2010 : R2015 | SPECIFICATION FOR PERFORMANCE-GRADED ASPHALT BINDER |
| AASHTO PP 85 : 2017 | PRACTICE FOR GRADING OR VERIFYING THE SEALANT GRADE (SG) OF A HOT-POURED ASPHALT CRACK SEALANT |
| AASHTO T 361 : 2016 | METHOD OF TEST FOR DETERMINING ASPHALT BINDER BOND STRENGTH BY MEANS OF THE BINDER BOND STRENGTH (BBS) TEST |
| AASHTO TP 123 : 2016 | METHOD OF TEST FOR MEASURING ASPHALT BINDER YIELD ENERGY AND ELASTIC RECOVERY USING THE DYNAMIC SHEAR RHEOMETER |
| AASHTO M 323 : 2013 | SPECIFICATION FOR SUPERPAVE VOLUMETRIC MIX DESIGN |
| AASHTO M 332 : 2014 | SPECIFICATION FOR PERFORMANCE-GRADED ASPHALT BINDER USING MULTIPLE STRESS CREEP RECOVERY (MSCR) TEST |
| AASHTO TP 91 : 2015 | METHOD OF TEST FOR DETERMINING ASPHALT BINDER BOND STRENGTH BY MEANS OF THE ASPHALT BOND STRENGTH (ABS) TEST |
| AASHTO R 29 : 2015 | PRACTICE FOR GRADING OR VERIFYING THE PERFORMANCE GRADE (PG) OF AN ASPHALT BINDER |
| AASHTO R 26 : 2001 : R2013 | PRACTICE FOR CERTIFYING SUPPLIERS OF PERFORMANCE-GRADED ASPHALT BINDERS |
| AASHTO TP 101 : 2012 : R2015 | METHOD OF TEST FOR ESTIMATING FATIGUE RESISTANCE OF ASPHALT BINDERS USING THE LINEAR AMPLITUDE SWEEP |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| DIN 43760:1987-09 | MEASUREMENT AND CONTROL - ELECTRICAL TEMPERATURE SENSORS - REFERENCES-TABLES FOR NICKEL RESISTORS FOR RESISTANCE THERMOMETERS |
| AASHTO R 66 : 2015 | PRACTICE FOR SAMPLING ASPHALT MATERIALS |
| AASHTO T 314 : 2012 | METHOD OF TEST FOR DETERMINING THE FRACTURE PROPERTIES OF ASPHALT BINDER IN DIRECT TENSION (DT) |
| AASHTO T 240 : 2013 | METHOD OF TEST FOR EFFECT OF HEAT AND AIR ON A MOVING FILM OF ASPHALT BINDER (ROLLING THIN-FILM OVEN TEST) |
| AASHTO R 29 : 2015 | PRACTICE FOR GRADING OR VERIFYING THE PERFORMANCE GRADE (PG) OF AN ASPHALT BINDER |
| AASHTO R 28 : 2012 | PRACTICE FOR ACCELERATED AGING OF ASPHALT BINDER USING A PRESSURIZED AGING VESSEL (PAV) |
| ASTM C 670 : 2015 : REDLINE | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.