• Shopping Cart
    There are no items in your cart

AS 4441(INT)-1996

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Oriented PVC (OPVC) pipes for pressure applications

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

30-06-2017

Language(s)

English

Published date

05-12-1996

€32.89
Excluding VAT

1 - AS 4441(Int)-1996 ORIENTED PVC (OPVC) PIPES FOR PRESSURE APPLICATIONS
4 - PREFACE
5 - CONTENTS
6 - FOREWORD
7 - SECTION 1 SCOPE AND GENERAL
7 - 1.1 SCOPE
7 - 1.2 REFERENCED DOCUMENTS
8 - 1.3 DEFINITIONS
8 - 1.3.1 Hoop stress
8 - 1.3.2 Hydrostatic design stress
8 - 1.3.3 Long-term hydrostatic stress
8 - 1.3.4 Out-of-roundness (sometimes referred to as ovality)
8 - 1.3.5 Pipe material temperature
8 - 1.3.6 Test pressure
8 - 1.3.7 Working pressure
8 - 1.4 NOTATION
8 - 1.5 CLASSIFICATION
9 - SECTION 2 GENERAL REQUIREMENTS
9 - 2.1 GENERAL
9 - 2.2 COMPOSITION
9 - 2.3 DIAMETER AND WALL THICKNESS
9 - 2.4 COLOUR
9 - 2.4.1 Series 1
9 - 2.4.2 Series 2
9 - 2.4.3 Other colour
9 - 2.5 LENGTH
9 - 2.5.1 Effective length
9 - 2.5.2 Witness mark
9 - 2.6 PIPE SPIGOT ENDS
9 - 2.7 SOCKETS FORMED ON PIPE
10 - 2.8 FREEDOM FROM DEFECTS
10 - 2.8.1 General
10 - 2.8.2 Pipe ends
10 - 2.9 STORAGE AND TRANSPORT
13 - SECTION 3 PERFORMANCE REQUIREMENTS
13 - 3.1 GENERAL
13 - 3.2 EFFECT ON WATER
13 - 3.3 VINYL CHLORIDE MONOMER
13 - 3.4 LIGHT TRANSMISSION
13 - 3.5 LONG TERM HYDROSTATIC PRESSURE TEST
13 - 3.6 IMPACT CHARACTERISTICS AT 0°C
13 - 3.7 SHORT TERM HYDROSTATIC PRESSURE TEST
13 - 3.8 HIGH TEMPERATURE TEST
13 - 3.9 JOINT HYDROSTATIC TEST
14 - 3.10 JOINT INFILTRATION TEST
14 - 3.11 REVERSION TEST
15 - SECTION 4 MARKING
16 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
16 - A1 SCOPE
16 - A2 STATISTICAL SAMPLING
16 - A3 PRODUCT CERTIFICATION
16 - A4 SUPPLIER'S QUALITY SYSTEM
17 - A5 OTHER MEANS OF ASSESSMENT
17 - A6 AUSTRALIAN WATER UTILITY REQUIREMENTS

Specifies requirements for oriented PVC (OPVC) pipe for pressure applications for use below ground and above ground where not exposed to direct sunlight, and for operational temperatures below 50 degrees Celsius.

CommentClosesDate
05-12-2000
Committee
PL-021
DocumentType
Standard
ISBN
0 7337 0864 1
Pages
11
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes

This Standard specifies requirements for oriented PVC (OPVC) pipe for pressure applications for use below ground, above ground where not exposed to direct sunlight, and for operational temperatures below 50 C.OPVC pipes in accordance with this Standard are intended for elastomeric ring jointing by integral sockets or by separate couplings. Solvent cement joints are not a specified jointing method for OPVC pipes.OPVC pipe manufactured to this Standard should be used and installed only in accordance with AS 2032 and AS 2566.

First published as AS 4441(Int)-1996.

AS 2566-1982 Plastics pipelaying design
AS/NZS 1462.15:1996 Methods of test for PVC pipes and fittings Method for determination of vinyl chloride monomer content (Reconfirmed 2017)
AS 1399-1990 Guide to AS 1199 - Sampling procedures and tables for inspection by attributes
AS 1199-1988 Sampling procedures and tables for inspection by attributes
AS/NZS 1477:1999 PVC pipes and fittings for pressure applications
AS 1462.17-1988 Methods of test for unplasticized PVC (UPVC) pipes and fittings Method for testing pressure pipe joints with elastomeric seals
AS 3500.0-1990 National Plumbing and Drainage Code Glossary of terms
AS 3855-1994 Suitability of plumbing and water distribution systems products for contact with potable water
AS/NZS 1462.1:1996 Methods of test for PVC pipes and fittings Method for determining the dimensions of pipes and fittings
AS 1462.3-1988 Methods of test for unplasticized PVC (UPVC) pipes and fittings Method for determining of impact characteristics of UPVC pipes
AS/NZS 1462.16:1996 Methods of test for PVC pipes and fittings - Method for high temperature testing of pipe
AS/NZS ISO 9004.1:1994 Quality management and quality system elements Guidelines
AS 1462.4-1984 Methods of test for unplasticized PVC (UPVC) pipes and fittings Method of determining reversion of UPVC pipes
AS 4020(INT)-1992 Products for use in contact with water intended for human consumption with regard to their effect on the quality of water
AS/NZS ISO 9000.1:1994 Quality management and quality assurance standards Guidelines for selection and use
AS 1462.6-1989 Methods of test for unplasticized PVC (UPVC) pipes and fittings Methods for hydrostatic pressure testing of UPVC pressure pipes
AS 2032-1977 Code of practice for installation of UPVC pipe systems
AS 1462.8-1984 Methods of test for unplasticized PVC (UPVC) pipes and fittings Method of test for liquid infiltration
AS/NZS 1462.14:1996 Methods of test for PVC pipes and fittings Method for determination of the light transmission of pipe (Reconfirmed 2017)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.