• Shopping Cart
    There are no items in your cart

AS/NZS 1260:1999

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

PVC pipes and fittings for drain, waste and vent applications

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

25-05-2024

Superseded by

AS/NZS 1260:2002

Published date

04-06-1999

€111.46
Excluding VAT

1 - AS/NZS 1260:1999 PVC PIPES AND FITTINGS FOR DRAIN, WASTE AND VENT APPLICATIONS
4 - PREFACE
6 - CONTENTS
8 - SECTION 1 SCOPE AND GENERAL
8 - 1.1 SCOPE
8 - 1.2 REFERENCED DOCUMENTS
9 - 1.3 DEFINITIONS
9 - 1.3.1 Effective seal
9 - 1.3.2 Effective sealing length
9 - 1.3.3 Fabricated fitting/assembly
10 - 1.3.4 Inside wall thickness
10 - 1.3.5 Maximum differential displacement
10 - 1.3.6 Minimum jointing compression conditions
10 - 1.3.7 Moulded fitting
10 - 1.3.8 Out-of-roundness (sometimes referred to as ovality)
10 - 1.3.9 Plain wall construction
10 - 1.3.10 Recycled PVC (Recyclate)
10 - 1.3.11 Ribbed or hollow profile construction
10 - 1.3.12 Sandwich construction
10 - 1.3.13 Sharp edge
10 - 1.3.14 Structured wall
11 - 1.4 RING BENDING STIFFNESS
11 - 1.5 NOTATION
11 - 1.6 CLASSIFICATION
13 - SECTION 2 GENERAL REQUIREMENTS
13 - 2.1 GENERAL
13 - 2.2 COMPOSITION
13 - 2.3 COLOUR
13 - 2.4 FREEDOM FROM DEFECTS
13 - 2.4.1 General
13 - 2.4.2 Spigot ends
13 - 2.5 REQUIREMENTS FOR ELASTOMERIC SEALS
14 - 2.6 SOLVENT CEMENTS
14 - 2.7 PACKAGING, STORAGE AND TRANSPORTATION
15 - SECTION 3 PERFORMANCE REQUIREMENTS
15 - 3.1 GENERAL
15 - 3.2 TESTS ON PIPES
15 - 3.2.1 Pipe impact characteristics at 20°C
15 - 3.2.2 Reversion (for plain wall pipes only)
15 - 3.2.3 Bond strength (for hollow profile wall pipes only)
15 - 3.2.4 Pipe stiffness
16 - 3.2.5 Ring flexibility test
16 - 3.2.6 Softening temperature (Vicat test)
16 - 3.2.7 Elevated temperature cycling test on structured wall pipes (Applicable up to and including size DN80)
16 - 3.3 TESTS ON MOULDED AND FABRICATED FITTINGS
16 - 3.3.1 Hydrostatic pressure test (Applicable only to fittings with inspection or test openings and to fabricated fittings)
16 - 3.3.2 Hydrostatic pressure test (Applicable to pan connectors)
16 - 3.3.3 Liquid infiltration test (Applicable only to fittings with inspection or test openings)
16 - 3.3.4 High temperature stress relief test (Applicable only to injection-moulded fittings)
17 - 3.3.5 Softening temperature (Vicat test)
17 - 3.3.6 Stiffness (for structured and hollow profile wall fittings only)
17 - 3.3.7 Elevated temperature cycling test on structured wall fittings (applicable up to and including size DN80)
17 - 3.4 TESTS ON ELASTOMERIC SEAL JOINTS
17 - 3.4.1 General
17 - 3.4.2 Hydrostatic pressure test
17 - 3.4.3 Liquid infiltration test
17 - 3.4.4 Contact width and pressure
17 - 3.5 ADDITIONAL TESTS ON PIPE AND FITTINGS CONTAINING RECYCLED PVC
17 - 3.5.1 Flattening test
17 - 3.5.2 Pipe high temperature test (Not applicable to intermediate layers of pipes or fittings of sandwich construction)
18 - SECTION 4 PIPES
18 - 4.1 GENERAL
18 - 4.2 DIAMETER AND WALL THICKNESS
18 - 4.3 LENGTH
18 - 4.4 PIPE SPIGOT ENDS
18 - 4.5 SOCKETS FORMED ON PIPE ENDS
22 - 4.6 MARKING
23 - 4.7 WITNESS MARK
24 - SECTION 5 MOULDED FITTINGS
24 - 5.1 GENERAL
24 - 5.2 DIMENSIONS OF MOULDED FITTINGS
24 - 5.2.1 General
24 - 5.2.2 Spigot ends
24 - 5.2.3 Sockets on moulded fittings
25 - 5.2.4 Tapered spigot ends for solvent cement jointing
26 - 5.3 WALL THICKNESS
27 - 5.4 GEOMETRY OF FITTINGS
27 - 5.4.1 Clear bore
27 - 5.4.2 Sweep junctions and bends
28 - 5.4.3 Eccentric tapers
28 - 5.4.4 Gullies
28 - 5.4.5 Vented bends
28 - 5.4.6 Pan connectors
28 - 5.5 THREADED END CONNECTIONS
29 - 5.6 TEST OPENINGS
29 - 5.6.1 General
30 - 5.6.2 Doors or insert plugs
30 - 5.6.3 Sealing rings
30 - 5.6.4 Threaded caps
30 - 5.7 INSPECTION OPENINGS
31 - 5.8 GRATINGS
32 - 5.9 BOLTED TRAP SCREWS
32 - 5.10 OVERFLOW RELIEF GRATINGS
32 - 5.10.1 Outlet
32 - 5.10.2 Inlet
32 - 5.11 MARKING
33 - SECTION 6 FABRICATED FITTINGS
33 - 6.1 GENERAL
33 - 6.2 MATERIALS
33 - 6.3 COMPLIANCE
33 - 6.4 MARKING
34 - SECTION 7 ELASTOMERIC SEAL JOINTS
34 - 7.1 GENERAL
34 - 7.2 MATERIALS
34 - 7.3 DESIGN
34 - 7.4 EFFECTIVE SEALING LENGTH
36 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
36 - A1 SCOPE
36 - A2 RELEVANCE
36 - A3 PRODUCT CERTIFICATION
36 - A4 MINIMUM SAMPLING AND TESTING FREQUENCY PLAN
36 - A4.1 General
36 - A4.2 Retesting
37 - A4.3 Rejection after retest
39 - APPENDIX B - TYPICAL RANGE OF MOULDED FITTINGS FOR DWV APPLICATIONS

Specifies requirements for PVC pipes and fittings for sewer, drain, waste and vent applications above or below ground and intended to be used where the pipeline is operating under gravity flow and the operating pressure is low. Includes requirements for both plain and structured wall pipes and fittings.

Committee
PL-021
DocumentType
Standard
ISBN
0 7337 2784 0
Pages
42
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

This Standard specifies requirements for PVC pipes and fittings for sewer, drain, waste and vent applications above-ground or below ground and intended to be used where the pipeline is operating under gravity flow and the operating pressure is low. The Standard includes requirements for both plain and structured wall pipes and fittings.NOTE: Pipes manufactured to this Standard should only be used and installed in accordance with AS 2032, AS/NZS 2566.1, AS 3500 and NZS 7643.Methods of demonstrating compliance with this Standard are given in Appendix A.

First published in Australia as part of AS K138-1963 and AS A160-1969.
Second edition AS K138-1967.
Third edition AS K138-1969.
AS K138-1969 and part of AS A160-1969 revised, amalgamated and redesignated as AS 1415.1-1974.
AS A160-1969 revised and redesignated in part as AS 1415.2-1974, AS 1415.3-1974 and AS 1415.5-1974.
Second edition AS 1415.1-1984.
Second edition AS 1415.3-1984.
AS 1415.4 first published 1974.
AS 1415.2-1974 and AS 1415.4-1974 revised, amalgamated and redesignated as AS 1415.2-1984.
AS 1415.5-1974 revised and redesignated as AS 1415.4-1984.
AS 1260.1 first published 1974.
AS 1260.2 first published 1974.
AS 1260.3 first published 1974.
AS 1260.4 first published 1974.
AS 1260.5 first published 1974.
AS 2340 first published 1980.
AS 1260.1-1974 and part of AS 1260.4-1974 revised, amalgamated and redesignated as AS 1260.1-1984.
AS 1260.2-1974 and part of AS 1260.4-1974 revised, amalgamated and redesignated as AS 1260.2-1984.
Second edition AS 1260.3-1984.
AS 1260.5-1974 revised and redesignated as AS 1260.4-1984.
Second edition AS 1260.5-1993.
First published in New Zealand in part as NZS 7641:1978, NZS 7642:1971 and NZS 7649:1988.
AS 1260.1-1984, AS 1260.2-1984, AS 1260.3-1984, AS 1260.4-1984, AS 1260.5-1993, AS 1415.1-1984, AS 1415.2-1984, AS 1415.3-1984, AS 1415.4-1984, AS 2340-1980, NZS 7641:1978, NZS 7642:1971 and NZS 7649:1988 jointly revised, amalgamated and redesignated as AS/NZS 1260:1996.
Second edition 1999.

AS/NZS 3500.1.2:1998 National plumbing and drainage Water supply - Acceptable solutions
AS/NZS 3500.4.2:1997 National Plumbing and Drainage Hot water supply systems - Acceptable solutions
AS/NZS 1254:2002 PVC pipes and fittings for storm and surface water applications
AS/NZS 3500.5:2000 Plumbing and Drainage Domestic installations
MP 52-2001 Manual of authorization procedures for plumbing and drainage products
AS 1589-2001 Copper and copper alloy waste fittings (Reconfirmed 2018)
AS 4799-2000 Installation of underground utility services and pipelines within railway boundaries
AS/NZS 3500.3.2:1998 National plumbing and drainage Stormwater drainage - Acceptable solutions

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.