AS/NZS 2492:2007
Redesignated
A redesignated Standard is one that has had its number changed. This could be the main number, the part number or the sub-part number.
Cross-linked polyethylene (PE-X) pipes for pressure applications
31-07-2007
Specifies requirements for cross-linked polyethylene pipes for the conveyance of fluids under pressure.
Committee |
PL-006
|
DocumentType |
Standard
|
ProductNote |
Redesignated to AS 2492:2007 by Amendment 1.
|
PublisherName |
Standards Australia
|
Status |
Redesignated
|
SupersededBy | |
Supersedes |
This Standard specifies requirements for cross-linked polyethylene pipes for the conveyance of fluids under pressure. Such fluids include, but are not restricted to, water, wastewater, slurries, compressed air, and fuel gas. Fuel gas includes natural gas, liquefied petroleum gas (LPG) in the vapour phase and LPG/air mixtures. The partial pressure of the LPG is not to exceed 300 kPa absolute. Pipes intended for the transmission of fuel gas are hereinafter referred to as ‘gas pipes’ and are not be operated at pressures above 1600 kPa gauge.
First published as AS 2492-1981.
Second edition 1994.
Jointly revised and designated AS/NZS 2492:2007.
AS/NZS 1462.19:2006 | Methods of test for plastics pipes and fittings C-ring test for fracture toughness of PVC pipes (Reconfirmed 2017) |
AS/NZS 1462.1:2006 | Methods of test for plastics pipes and fittings Method for determining the dimensions of pipes and fittings (Reconfirmed 2024) |
AS/NZS 1462.15:1996 | Methods of test for PVC pipes and fittings Method for determination of vinyl chloride monomer content (Reconfirmed 2017) |
AS/NZS 4129:2000 | Fittings for polyethylene (PE) pipes for pressure applications |
AS/NZS 3500.0:2003 | Plumbing and drainage Glossary of terms |
AS/NZS 1462.11:1996 | Methods of test for PVC pipes and fittings Method for high temperature stress-relief testing of fittings (Reconfirmed 2017) |
HB 18.28-2005 | Conformity assessment - Guidance on a third-party certification system for products |
AS/NZS 1462.13:2006 | Methods of test for plastics pipes and fittings Method for the determination of elastomeric seal joint contact width and pressure (Reconfirmed 2017) |
AS/NZS 4020:2005 | Testing of products for use in contact with drinking water |
AS 1199.1-2003 | Sampling procedures for inspection by attributes Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (Reconfirmed 2016) |
AS/NZS 1462.16:2006 | Methods of test for plastics pipes and fittings Method for high temperature testing of pipe (Reconfirmed 2017) |
AS/NZS 1462.6:1998 | Methods of test for plastics pipes and fittings - Method for hydrostatic pressure testing of pipes |
AS/NZS 1462.29:2006 | Methods of test for plastics pipes and fittings Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003, MOD) |
AS/NZS 1462.14:1996 | Methods of test for PVC pipes and fittings Method for determination of the light transmission of pipe (Reconfirmed 2017) |
AS/NZS 1462.10:1998 | Methods of test for plastics pipes and fittings Method for hydrostatic pressure testing of fittings and elastomeric seal joints for non-pressure applications (Reconfirmed 2017) |
AS/NZS 1462.27:2003 | Methods of test for plastics pipes and fittings Determination of toluene extract of carbon black (Reconfirmed 2017) |
AS/NZS 3500.4:2015 | Plumbing and drainage Heated water services |
AS/NZS 3500.1:2018 | Plumbing and drainage Water Services |
AS/NZS 4645.1:2018 | Gas distribution networks Network management |
AS 4176.8-2010 | Multilayer pipes for pressure applications Multilayer pipe systems for consumer gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) - Specifications for systems (ISO 17484-1:2006, MOD) |
AS/NZS 3500.5:2012 | Plumbing and drainage Housing installations |
AS/NZS 3500.4:2003 | Plumbing and drainage Heated water services |
MP 52-2005 | Manual of authorization procedures for plumbing and drainage products |
AS 4176-1994 | Polyethylene/aluminium and cross-linked polyethylene/aluminium macro-composite pipe systems for pressure applications |
AS/NZS 4020:2018 | Testing of products for use in contact with drinking water |
AS/NZS 5601.1:2013 | Gas installations General installations |
AS 2537-1994 | Mechanical jointing fittings for use with cross-linked polyethylene (PE-X) pipe for hot and cold water applications |
AS/NZS 2537.3:2011 | Mechanical jointing fittings for use with crosslinked polyethylene (PE-X) for pressure applications Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Fitness for purpose of the system (ISO 15875-5:2003, MOD) (Reconfirmed 2022) |
AS/NZS 3500.4:2018 | Plumbing and drainage Heated water services |
AS/NZS 3500.1:2003 | Plumbing and drainage Water services |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.