• Shopping Cart
    There are no items in your cart

AS/NZS 4200.1:1994

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Pliable building membranes and underlays Materials

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

29-05-2024

Superseded by

AS 4200.1:2017

Published date

18-07-1994

€32.89
Excluding VAT

Specifies the requirements for materials suitable for use as a pliable building membrane (also known as underlay) when it is intended to act as a sarking membrane or thermal insulation, or a vapour barrier in a domestic, commercial or industrial building. It does not specify the thermal insulation requirements, nor does it include materials for use in air handling ducts.

Committee
BD-048
DocumentType
Standard
ISBN
0 7262 9011 4
Pages
10
ProductNote
See also AS 1736-1975 and AS 1903-1976
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

This Standard sets out the requirements for materials suitable for use as a pliable building membrane (also known as underlay) in any of the following circumstances:(a) When it is intended to act as a sarking membrane or thermal insulation or a vapour barrier when installed in a building structure.(b) When installed either independently, or as a facing to other materials such as insulation materials.(c) When installed in domestic, commercial or industrial buildings.Materials for use in air-handling ducts are generally outside the scope of this Standard. However, this document may be called up by a future the air-handling duct Standard.Vapour barriers used under concrete slabs are outside the scope of this Standard.NOTES:1 Methods for determining compliance with this Standard are given in Appendix A.2 Thermal insulation requirements are specified in AS 2627.3 This Standard will be referenced in the Building Code of Australia by way of BCA Amendment 7 intended for publication in October 1994, thereby superseding the previous editions of AS 1736 - 1975 and AS 1903 - 1976, which will be withdrawn 12 months from the date of publication of this Standard.Users are advised that when BCA Amendment 7 is issued, it will not necessarily be gazetted in each State/Territory at the time of printing.

Originated in Australia as AS 4179-1994.
Previous and first joint edition AS/NZS 4179:1997.
Third edition 2014.

AS 3904.1-1987 Quality management and quality system elements Guidelines
AS 1170.2-1989 Minimum design loads on structures (known as the SAA Loading Code) Wind loads
AS 4055-2006 Wind loads for housing
AS/NZS 4201.6:1994 Pliable building membranes and underlays - Methods of test Surface water absorbency
HB 18.44-1991 Guidelines for third-party certification and accreditation - Guide 44: General rules for ISO or IEC international third-party certification schemes for products
AS 1399-1990 Guide to AS 1199 - Sampling procedures and tables for inspection by attributes
AS/NZS 1301.448S:2007 Methods of test for pulp and paper Tensile strength of paper and paperboard (constant rate of elongation method)
AS 1199-1988 Sampling procedures and tables for inspection by attributes
AS 1530.2-1993 Methods for fire tests on building materials, components and structures Test for flammability of materials (Reconfirmed 2016)
AS 1736-1975 Code of practice for pliable roof sarking
AS/NZS 4201.4:1994 Pliable building membranes and underlays - Methods of test Resistance to water penetration (Reconfirmed 2020)
AS 4055-1992 Wind loads for housing
AS/NZS 4201.5:1994 Pliable building membranes and underlays - Methods of test Emittance (Reconfirmed 2020)
AS/NZS 4201.2:1994 Pliable building membranes and underlays - Methods of test Resistance to wet delamination (Reconfirmed 2020)
AS/NZS 4201.3:1994 Pliable building membranes and underlays - Methods of test Shrinkage (Reconfirmed 2020)
AS/NZS 4201.0:1994 Pliable building membranes and underlays - Methods of test General introduction and list of methods (Reconfirmed 2020)
AS 1301.423RP-1989 Methods of test for pulp and paper (metric units) Folding endurance of paper - Kohler-Molin methods
AS 3900.1-1987 Quality management and quality assurance Standards Guidelines for selection and use
AS 1903 TO 1904-1976 Reflective foil laminate
AS 2627.1-1993 Thermal insulation of dwellings Thermal insulation of roof/ceilings and walls in dwellings
AS/NZS 1301.423RP:1997 Methods of test for pulp and paper Folding strength of paper - Kohler-Molin method
AS/NZS 1170.2:2002 Structural design actions Wind actions
AS 1301.448S-1991 Methods of test for pulp and paper Tensile strength of paper and paperboard (Constant rate of elongation method)
AS 2001.2.19-1988 Methods of test for textiles Physical tests - Determination of bursting force of textile fabrics - Ball burst method (Reconfirmed 2016)
AS/NZS 4201.1:1994 Pliable building membranes and underlays - Methods of test Resistance to dry delamination (Reconfirmed 2020)

AS 2050-1995 Installation of roof tiles
AS 2050-2002 Installation of roof tiles
AS 3959-1999 Construction of buildings in bushfire-prone areas
AS 4597-1999 Installation of roof slates and shingles (Non-interlocking type) (Reconfirmed 2015)
HB 67-1995 Concrete practice on building sites
AS 4254.2-2012 Ductwork for air-handling systems in buildings Rigid duct
AS/NZS 2589:2007 Gypsum linings - Application and finishing
AS 4254-2002 Ductwork for air-handling systems in buildings
AS/NZS 2589:2017 Gypsum linings - Application and finishing
AS/NZS 4859.1:2002 Materials for the thermal insulation of buildings General criteria and technical provisions
AS/NZS 4200.2:1994 Pliable building membranes and underlays Installation requirements

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.