AS/NZS 4765:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Modified PVC (PVC-M) pipes for pressure applications
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
03-06-2024
English
20-09-2007
Important note : Users cannot be edited or removed once added to your Multi user PDF.Specifies requirements for pipes, integral joints and post-formed bends of PVC-M for the conveyance of water and wastewater under pressure.
| Committee |
PL-021
|
| DocumentType |
Standard
|
| ISBN |
0 7337 8383 X
|
| Pages |
35
|
| PublisherName |
Standards Australia
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
This Standard specifies requirements for pipes, integral joints and post-formed bends of PVC-M for the conveyance of water and wastewater under pressure. The pipes are intended for installation below ground, and above ground where they are not exposed to direct sunlight.NOTES:1 Relevant installation requirements for pipe systems, including PVC-M pressure pipes manufactured to this Standard and the associated fittings are covered by AS/NZS 2032, AS/NZS 2566.2 and the AS/NZS 3500 series, as applicable.2 If it is intended to use pipes complying with this Standard for the conveyance of fluids other than water, the manufacturer should be consulted.3 Two series of pipes are specified (see the Foreword in this Standard).
Originated as AS/NZS 4765(Int):2000.
This edition 2007.
| HB 18.28-2005 | Conformity assessment - Guidance on a third-party certification system for products |
| AS/NZS 4020:2005 | Testing of products for use in contact with drinking water |
| AS/NZS 1462.4:2002 | Methods of test for plastics pipes and fittings Method for determining reversion of plastics pipes (Reconfirmed 2017) |
| AS/NZS 3500.0:2003 | Plumbing and drainage Glossary of terms |
| AS 1199.1-2003 | Sampling procedures for inspection by attributes Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (Reconfirmed 2016) |
| AS/NZS 3879:2006 | Solvent cements and priming fluids for PVC (PVC-U and PVC-M) and ABS pipes and fittings |
| AS/NZS 1462.5:2002 | Methods of test for plastics pipes and fittings Vicat softening temperature (Reconfirmed 2017) |
| AS/NZS 3500.1:2003 | Plumbing and drainage Water services |
| AS/NZS 1462.16:2006 | Methods of test for plastics pipes and fittings Method for high temperature testing of pipe (Reconfirmed 2017) |
| AS 1646.1-2000 | Elastomeric seals for waterworks purposes - General requirements |
| AS/NZS 1462.6:1998 | Methods of test for plastics pipes and fittings - Method for hydrostatic pressure testing of pipes |
| AS/NZS 3500.5:2000 | Plumbing and Drainage Domestic installations |
| AS/NZS 3500.3:2003 | Plumbing and drainage Stormwater drainage |
| AS/NZS 2566.2:2002 | Buried flexible pipelines Installation (Reconfirmed 2016) |
| AS/NZS 1462.29:2006 | Methods of test for plastics pipes and fittings Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003, MOD) |
| AS/NZS 1462.1:2006 | Methods of test for plastics pipes and fittings Method for determining the dimensions of pipes and fittings (Reconfirmed 2024) |
| AS/NZS 1462.15:1996 | Methods of test for PVC pipes and fittings Method for determination of vinyl chloride monomer content (Reconfirmed 2017) |
| AS 1646.3-2000 | Elastomeric seals for waterworks purposes - Material requirements for pipe joints seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds |
| AS/NZS 3500.2:2003 | Plumbing and drainage Sanitary plumbing and drainage |
| AS/NZS 2032:2006 | Installation of PVC pipe systems (Reconfirmed 2024) |
| AS/NZS 3500.4:2003 | Plumbing and drainage Heated water services |
| AS 1646.2-2000 | Elastomeric seals for waterworks purposes Material requirements for pipe joint seals used in water and wastewater applications - Specifies by prescription formulation |
| AS 3571.2-2009 | Plastics piping systems - Glass reinforced thermoplastics (GRP) systems based on unsaturated polyester (UP) resin Pressure and non-pressure water supply (ISO 10639:2004, MOD) |
| AS/NZS 1254:2010 | PVC-U pipes and fittings for stormwater and surface water applications (Reconfirmed 2024) |
| AS/NZS 3518:2013 | Acrylonitrile butadine styrene (ABS) compounds, pipes and fittings for pressure applications (Reconfirmed 2024) |
| AS 1646-2007 | Elastomeric seals for waterworks purposes (Reconfirmed 2018) |
| AS/NZS 1260:2009 | PVC-U pipes and fittings for drain, waste and vent application |
| AS/NZS 1260:2017 | PVC-U pipes and fittings for drain, waste and vent applications |
| AS/NZS 3879:2011 | Solvent cements and priming fluids for PVC (PVC-U and PVC-M) and ABS and ASA pipes and fittings |
| AS/NZS 4793:2009 | Mechanical tapping bands for waterworks purposes |
| AS 3571.1-2009 | Plastics piping systems - Glass reinforced thermoplastics (GRP) systems based on unsaturated polyester (UP) resin Pressure and non-pressure drainage and sewerage (ISO 10467:2004, MOD) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.