• Shopping Cart
    There are no items in your cart

ASTM A 1053/A1053M : 2012 : R2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Welded Ferritic-Martensitic Stainless Steel Pipe

Available format(s)

Hardcopy , PDF

Superseded date

29-04-2022

Language(s)

English

Published date

02-10-2017

€59.22
Excluding VAT

CONTAINED IN VOL. 01.01, 2017 Defines seam welded ferritic-martensitic (dual phase) stainless steel pipe intended for abrasive and general corrosion service, manufactured with or without the addition of filler metal.

Committee
A 01
DocumentType
Standard
Pages
4
ProductNote
Reconfirmed 2017
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers seam welded ferritic-martensitic (dual phase) stainless steel pipe intended for abrasive and general corrosion service, manufactured with or without the addition of filler metal. Nominal sizes are NPS 2 to NPS 36 inclusive, with nominal (average) wall thickness up to 0.75-in. (19 mm).

1.2The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents. Therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation is specified in the order.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM A 370 : 2021 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1016/A1016M : 2002 Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
SAE J1086_201210 Numbering Metals and Alloys
ASME PV CODE 9 : 2017 BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS
ASTM A 941 : 2022 Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
ASME B36.10 : 1979 WELDED AND SEAMLESS WROUGHT STEEL PIPE
ASTM A 370 : 2020 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
ASTM E 527 : 2016 : REDLINE Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASTM A 370 : 2011 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 941 : 2009 Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
ASME B36.19 : 1976 STAINLESS STEEL PIPE
ASTM A 941 : 2018 Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.