ASTM A 240/A240M : 2024 : REV A
Current
The latest, up-to-date edition.
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
Hardcopy , PDF
English
15-10-2024
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
12
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 1966 : 2012 : R2023 | Standard Specification for Dough Divider and Rounding Machines |
ASTM A 1069/A1069M : 2023 | Standard Specification for Stainless Steel Laser and Laser Hybrid Welded Bars, Plates, Sharp-Cornered Profile (SCP), and Built-up Shapes |
ASTM D 3603 : 2020 | Standard Test Method for Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method) |
ASTM A 666/A666M : 2024 | Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar |
ASTM B 625 : 2021 | Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy, Ni-Fe-Cr-Si Alloy, <brk />Cr-Ni-Fe-N Low-Carbon Alloy, Fe-Ni-Cr-Mo-Cu-N Alloy, and <brk/>Ni-Fe-Cr-Mo-N Alloy Plate, Sheet, and Strip |
ASTM D 4054 : 2024 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM F 1910 : 1998 : R2022 | Standard Specification for Long Barbed Tape Obstacles |
ASTM F 1203 : 2022 | Standard Specification for Washing Machines—Pot, Pan, and Utensil, Heat Sanitizing, Commercial Rotary Conveyor Type |
ASTM A 480/A480M : 2024 | Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
ASTM C 1173 : 2022 | Standard Specification for Flexible Transition Couplings for Underground Piping Systems |
ASTM F 2645 : 2021 | Standard Specification for Bun Slicing Machines |
ASTM F 3215 : 2022 | Standard Specification for Food Waste Dehydrators |
ASTM D 8507 : 2023 | Standard Specification for High Load Multi-Rotational Disc Bearings for Bridges and Structures |
ASTM C 1767 : 2021 | Standard Specification for Stainless Steel Jacketing for Insulation |
ASTM F 1114 : 2022 | Standard Specification for Heat Sanitizing Commercial Pot, Pan, and Utensil Washing Machines, Stationary Rack, Water-Driven Rotary Spray Type |
ASTM F 1602 : 2012 : R2023 | Standard Specification for Kettles, Steam-Jacketed, 20 to 200 gal (75.7 to 757 L), Floor or Wall Mounted, Direct Steam, Gas and Electric Heated |
ASTM C 425 : 2022 | Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings |
ASTM F 1047 : 2017 : R2023 | Standard Specification for Frying and Braising Pans, Tilting Type |
ASTM F 2643 : 2020 | Standard Specification for Powered Pot, Pan and Utensil Washing Sinks |
ASTM A 1127/A1127M : 2023 | Standard Specification for Stainless Steel Laser and Laser-Hybrid Welded, Sharp-Cornered Profile (SCP) or Built-Up Rounded Corner Square, Rectangular, and Special Shape Structural Tube |
ASTM C 1572/C1572M : 2023 | Standard Guide for Dry Lead Glass and Oil-Filled Lead Glass Radiation Shielding Window Components for Remotely Operated Facilities |
ASTM A 264 : 2012 : R2019 | Standard Specification for Stainless Chromium-Nickel Steel-Clad Plate |
ASTM C 1802 : 2023 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
ASTM F 857 : 2017 | Standard Specification for Hot Water and Chemical Sanitizing Commercial Dishwashing Machines, Stationary Rack Type |
ASTM D 2595 : 2022 | Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range |
ASTM D 5534 : 1994 : R2018 | Standard Test Method for Vapor-Phase Rust-Preventing Characteristics of Hydraulic Fluids |
ASTM C 1644 : 2006 : R2017 | Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes |
ASTM C 1696 : 2020 | Standard Guide for Industrial Thermal Insulation Systems |
ASTM A 358/A358M : 2024 | Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications |
ASTM F 859 : 2021 | Standard Specification for Heat-Sanitizing Commercial Dishwashing Machines, Multiple Tank, Conveyor Rack Type |
ASTM F 1360 : 2024 | Standard Specification for Ovens, Microwave, Electric |
ASTM A 947M : 2016 | Standard Specification for Textured Stainless Steel Sheet [Metric] |
ASTM C 852/C852M : 2017 : R2022 | Standard Guide for Design Criteria for Plutonium Gloveboxes |
ASTM D 665 : 2023 | Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water |
ASTM F 1217 : 2017 : R2023 | Standard Specification for Cooker, Steam |
ASTM F 3110 : 2014 : R2024 | Standard Practice for Proper Use of Mechanical Trenchless Point Repair Sleeve with Locking Gear Mechanism for Pipes of Varying Inner Diameter and Offset Joints |
ASTM F 1202 : 2022 | Standard Specification for Washing Machines, Heat Sanitizing, Commercial, Pot, Pan, and Utensil Vertically Oscillating Arm Type |
ASTM F 821/F821M : 2023 | Standard Specification for Domestic Use Doors and Frames, Steel, Interior, Marine |
ASTM C 1861 : 2023 : REV A | Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster |
ASTM C 1533 : 2015 : R2022 | Standard Guide for General Design Considerations for Hot Cell Equipment |
ASTM C 1277 : 2020 | Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
ASTM F 2891 : 2015 : R2020 : EDT 1 | Standard Specification for Commercial Bulk Milk Dispensers, Mechanically Refrigerated |
ASTM F 1604 : 2015 : R2020 : EDT 1 | Standard Specification for Freezers, Ice Cream, Soft Serve, Shake |
ASTM D 942 : 2023 : REV A | Standard Test Method for Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method |
ASTM F 825 : 2022 | Standard Specification for Drawers, Furniture, Marine, Steel |
ASTM F 782 : 2019 : R2024 | Standard Specification for Doors, Furniture, Marine |
ASTM F 2646 : 2021 | Standard Specification for Bread Slicing Machines |
ASTM F 1150 : 2022 | Standard Specification for Commercial Food Waste Pulper and Waterpress Assembly |
ASTM D 3966/D3966M : 2022 | Standard Test Methods for Deep Foundation Elements Under Static Lateral Load |
ASTM C 1767M : 2021 | Standard Specification for Stainless Steel Jacketing for Insulation |
ASTM C 1423 : 2021 | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
ASTM C 1540 : 2020 | Standard Specification for Heavy-Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
ASTM D 2878 : 2021 | Standard Test Method for Estimating Apparent Vapor Pressures and Molecular Weights of Lubricating Oils |
ASTM A 778/A778M : 2024 : REV A | Standard Specification for Welded, Unannealed Austenitic Stainless Steel Tubular Products |
ASTM C 692 : 2013 : R2023 | Standard Test Method for Evaluating the Influence of Thermal Insulations on External Stress Corrosion Cracking Tendency of Austenitic Stainless Steel |
ASTM F 1073 : 2019 : R2024 | Standard Specification for Door Fittings, for Watertight /Gastight /Airtight, Weathertight, and Non-Tight Doors, for Marine Use |
ASTM F 1718 : 2001 : R2019 | Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps |
ASTM D 972 : 2022 | Standard Test Method for Evaporation Loss of Lubricating Greases and Oils |
ASTM A 263 : 2012 : R2019 | Standard Specification for Stainless Chromium Steel-Clad Plate |
ASTM F 1267 : 2018 : R2023 | Standard Specification for Metal, Expanded, Steel |
ASTM A 928/A928M : 2014 : R2021 | Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler Metal |
ASTM A 774/A774M : 2024 | Standard Specification for As-Welded Wrought Austenitic Stainless Steel Fittings for General Corrosive Service at Low and Moderate Temperatures |
ASTM F 1603 : 2017 : R2023 | Standard Specification for Kettles, Steam-Jacketed, 32 oz to 20 gal (1 to 75.7 L), Tilting, Table Mounted, Direct Steam, Gas and Electric Heated |
ASTM B 506 : 2022 | Standard Specification for Copper-Clad Stainless Steel Sheet and Strip for Building Construction |
ASTM A 1128 : 2024 | Standard Specification for Stainless Steel Shielded, Rubber Gasketed Couplings Having an Integral Restraint Feature for Joining Hubless Cast Iron Soil Pipes and Fittings Where External Restraint Is Required |
ASTM F 2332 : 2006 : R2022 | Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components |
ASTM D 5977 : 2023 | Standard Specification for High Load Rotational Spherical Bearings for Bridges and Structures |
ASTM F 1387 : 2023 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
ASTM F 824 : 2022 | Standard Specification for Tables, Mess, Marine, Steel |
ASTM F 1511 : 2018 : R2023 | Standard Specification for Mechanical Seals for Shipboard Pump Applications |
ASTM A 370 : 2024 : REV A | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.