ASTM A 27/A27M : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Steel Castings, Carbon, for General Application
02-05-2020
English
01-05-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 01.02, 2017 Defines carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength.
| Committee |
A 01
|
| DevelopmentNote |
Supersedes ASTM A 27. (04/2002)
|
| DocumentType |
Redline
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength.
Note 1:The grades covered by this specification represent materials that are suitable for assembly with other steel castings or wrought steel parts by fusion welding. It is not intended to imply that all these grades possess the same degree of weldability or that the same welding techniques can be used on all castings. It is the responsibility of the purchaser to establish for himself a suitable welding technique.
1.2Several grades and two classes of steel castings are covered, as indicated below. The grade and class desired shall be specified by the purchaser.
1.2.1Grade N-1—Chemical analysis only.
1.2.2Grade N-2—Heat treated but not mechanically tested.
1.2.3Grade U-60-30 [415-205]—Mechanically tested but not heat treated.
1.2.4Grades 60-30 [415-205], 65-35 [450-240], 70-36 [485-250], and 70-40 [485-275]—Heat treated and mechanically tested.
1.2.5Class 1 and Class 2 steel castings shall be specified in accordance with 9.2.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| AWWA C301 : 2014 | PRESTRESSED CONCRETE PRESSURE PIPE, STEEL-CYLINDER TYPE |
| CSA S16S1 : 2005 | SUPPLEMENT NO. 1 TO CAN/CSA-S16-01, LIMIT STATES DESIGN OF STEEL STRUCTURES |
| MIL-DTL-613 Revision D:2014 | Grapnels, Marine, Trip Wire, and Crash Truck |
| AISC 350 : 99 ERRATA 2001 | LOAD AND RESISTANCE FACTOR DESIGN SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS |
| ASTM F 2798 : 2009 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
| ASTM F 2935 : 2012 | Standard Specification for Chocks, Panama, Mooring Cast Steel |
| ASTM F 2798 : 2009 : R2018 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
| MIL-DTL-12632 Revision E:2016 | LOUDSPEAKERS, PERMANENT MAGNET (ENCASED, 2-WATT, FUNGUS-, GUNBLAST-, AND IMMERSION-RESISTANT), GENERAL SPECIFICATION FOR |
| AASHTO LRFDLTS 1 : 1900 | LRFD SPECIFICATIONS FOR STRUCTURAL SUPPORTS FOR HIGHWAY SIGNS, LUMINAIRES, AND TRAFFIC SIGNALS |
| ASTM F 765 : 1993 : R2017 | Standard Specification for Wildcats, Ship Anchor Chain |
| MIL L 12632 : D | LOUDSPEAKER, PERMANENT MAGNET (ENCASED, 2 WATT, FUNGUS, GUNBLAST, AND IMMERSION RESISTANT), GENERAL SPECIFICATION FOR |
| CSA S37 : 2013 | ANTENNAS, TOWERS, AND ANTENNA-SUPPORTING STRUCTURES |
| ASTM F 2798 : 2009 : R2014 : EDT 1 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
| ASTM F 1510 : 2007 : R2013 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
| ASTM F 1106 : 1987 : R2012 | Standard Specification for Warping Heads, Rope Handling (Gypsy Head, Capstan Head) |
| ASME A17.7 : 2007 : R2012 | PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS |
| ASME A17.7 : 2007 | PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS |
| ASTM C 361M : 2016 : REDLINE | SPECIFICATION FOR REINFORCED CONCRETE LOW-HEAD PRESSURE PIPE [METRIC] |
| ASTM F 765 : 1993 : R1998 | Standard Specification for Wildcats, Ship Anchor Chain |
| ASTM A 488/A488M : 2017-05 | PRACTICE FOR STEEL CASTINGS, WELDING, QUALIFICATIONS OF PROCEDURES AND PERSONNEL |
| AWWA C507 : 2015 | BALL VALVES, 6 IN. THROUGH 60 IN. (150 MM THROUGH 1,500 MM) |
| MIL-DTL-2 Revision G:2006 | VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR |
| ASTM F 765 : 1993 : R2006 | Standard Specification for Wildcats, Ship Anchor Chain |
| ASTM F 937 : 1985 : R1991 | Specification for Chocks, Ship Mooring Cast Steel (Withdrawn 1997) |
| ASTM F 1106 : 1987 : R1998 | Standard Specification for Warping Heads, Rope Handling (Gypsy Head, Capstan Head) |
| ASTM A 781/A781M : 2018-02 | SPECIFICATION FOR CASTINGS, STEEL AND ALLOY, COMMON REQUIREMENTS, FOR GENERAL INDUSTRIAL USE |
| API 650 : 2013 | WELDED TANKS FOR OIL STORAGE |
| CSA B44.7 : 2007 : R2012 | PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS |
| ASME A17.7-2007/CSA B44.7-07 (R2017) | Performance-Based Safety Code for Elevators and Escalators (Bi-National standard, with ASME A17.7) |
| CSA B44.7 : 2007 | PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS |
| ASTM F 765 : 1993 : R2012 : EDT 1 | Standard Specification for Wildcats, Ship Anchor Chain |
| ASTM F 915 : 1985 | Specification for Bitts, Ship Mooring, Cast Steel (Double Barrel) (Withdrawn 1995) |
| ASTM F 2936 : 2012 | Standard Specification for Chocks, Ship Mooring, Cast Steel |
| AWWA E103 : 2015 | HORIZONTAL AND VERTICAL LINE-SHAFT PUMPS |
| AWWA C509 : 2015 | RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE |
| NFPA 22 : 2018 | WATER TANKS FOR PRIVATE FIRE PROTECTION |
| ASTM F 1106 : 1987 : R2006 | Standard Specification for Warping Heads, Rope Handling (Gypsy Head, Capstan Head) |
| ASTM F 1510 : 2007 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
| ASTM F 936 : 1985 : R1991 | Specification for Chocks, Panama, Mooring Cast Steel (Withdrawn 1997) |
| CSA S16 : 2014 | DESIGN OF STEEL STRUCTURES |
| API 650 : 2013+ADD 3 : 2018 | WELDED TANKS FOR OIL STORAGE |
| API 650 CHINESE : 2013 | WELDED TANKS FOR OIL STORAGE |
| AISC 335 : 89 SUPP 1 1999 | SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS - ALLOWABLE STRESS DESIGN, PLASTIC DESIGN |
| ASTM A 148/A148M : 2015-09 | SPECIFICATION FOR STEEL CASTINGS, HIGH STRENGTH, FOR STRUCTURAL PURPOSES |
| CSA S16.1 : 0 | LIMIT STATES DESIGN OF STEEL STRUCTURES |
| WW-T-696 Revision E:1984 | TRAPS, STEAM |
| ANSI/AWWA C300 : 2016 | REINFORCED CONCRETE PRESSURE PIPE, STEEL - CYLINDER TYPE |
| AWWA C515 : 2015 | REDUCED-WALL, RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE |
| AWWA C302 : 2016 | REINFORCED CONCRETE PRESSURE PIPE, NONCYLINDER TYPE |
| AWS D5.2 : 1984 | WELDED STEEL ELEVATED TANKS, STANDPIPES, AND RESERVOIRS FOR WATER STORAGE, STANDARD FOR, |
| ASTM C 361 : 2019 : REDLINE | SPECIFICATION FOR REINFORCED CONCRETE LOW-HEAD PRESSURE PIPE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.