ASTM A 276/A276M : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Stainless Steel Bars and Shapes
18-08-2023
English
21-03-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 01.03, 2017 Defines hot-finished or cold-finished bars except bars for reforging.
| Committee |
A 01
|
| DevelopmentNote |
Supersedes ASTM A 276. (02/2015)
|
| DocumentType |
Redline
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1). It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types (Note 2) for general corrosion resistance and high-temperature service are covered in a separate specification.
Note 1:For bars for reforging, see Specification A314.
Note 2:For free-machining stainless bars designed especially for optimum machinability, see Specification A582/A582M.
Note 3:There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol. 02.04.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
| ASTM A 1082/A1082M : 2016 : REDLINE | Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications |
| MIL-DTL-18030 Revision F:2018 | Valves, Control, Air-Diaphragm-Operated (Complete with Pneumatic Instrumentation) |
| AASHTO M 292M/M 292 : 2015 | SPECIFICATION FOR CARBON AND ALLOY STEEL NUTS FOR BOLTS FOR HIGH-PRESSURE OR HIGH-TEMPERATURE SERVICE, OR BOTH |
| MIL-DTL-18436 Revision G:2017 | Valves, Check - Bronze -and Steel-Body |
| MIL-DTL-28748-17 Revision B:2016 | CONNECTORS, ELECTRICAL, RECTANGULAR, RACK AND PANEL, HARDWARE FOR |
| MIL-DTL-6001 Revision B:2013 | FITTINGS; AIRCRAFT, SOLDER TYPE, TUBE |
| AWWA C512 : 2015 | AIR-RELEASE, AIR/VACUUM, AND COMBINATION AIR VALVES FOR WATER AND WASTEWATER SERVICE |
| AWWA C515 : 2015 | REDUCED-WALL, RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE |
| ANSI/AWWA C514 : 2015 | AIR VALVE AND VENT INFLOW PREVENTER ASSEMBLIES FOR POTABLE WATER DISTRIBUTION SYSTEM AND STORAGE FACILITIES |
| AWWA E103 : 2015 | HORIZONTAL AND VERTICAL LINE-SHAFT PUMPS |
| ACI 301 : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
| AWWA C541 : 2016 | HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES |
| SAEITC TS220-1 | TS220 Technical Specification for Self Locking Union Nuts (Unified Threads) Manufactured from INCO718 Material.1270 MPa (185000 lbf/in2) Minimum Tensile Strength at Room Temperature |
| AASHTO M 334M/M 334 : 2017 | SPECIFICATION FOR UNCOATED, CORROSION-RESISTANT, DEFORMED AND PLAIN CHROMIUM ALLOYED, BILLET-STEEL BARS FOR CONCRETE REINFORCEMENT AND DOWELS |
| ASME B31.3:2016 | PROCESS PIPING |
| ASTM A 955/A 955M : 2018-02 | SPECIFICATION FOR DEFORMED AND PLAIN STAINLESS-STEEL BARS FOR CONCRETE REINFORCEMENT |
| MIL-DTL-18866 Revision J:2015 | Fittings, Hydraulic Tube, Flared, 37 Degree and Flareless, General Specification for |
| ASTM A 1040 : 2017 : REDLINE | Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels |
| MSS SP 81 : 2017 | STAINLESS-STEEL OR STAINLESS-STEEL-LINED, BONNETLESS, KNIFE GATE VALVES WITH FLANGED ENDS |
| MIL-DTL-83798 Revision D:2008 | FITTING, RUBBER HOSE, LIGHTWEIGHT, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR |
| AASHTO MP 18M/MP 18 : 1900 | SPECIFICATION FOR UNCOATED, CORROSION-RESISTANT, DEFORMED AND PLAIN ALLOY, BILLET-STEEL BARS FOR CONCRETE REINFORCEMENT AND DOWELS |
| ASTM F 2854 : 2010 | Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing |
| ASTM F 2929 : 2017 : REDLINE | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| MS18197 Revision G:2016 | GUIDE PIN, ELECTRICAL CONNECTOR MALE AND FEMALE |
| MSS SP 99 : 2016 | INSTRUMENT VALVES |
| AASHTO T 375M/T 375 : 2017 | METHOD OF TEST FOR IDENTIFICATION OF IRON-BASED ALLOY STEEL BARS FOR CONCRETE REINFORCEMENT OR DOWELS BY HANDHELD X-RAY FLUORESCENCE (XRF) SPECTROMETER |
| MIL-DTL-52525 Revision F:2008 | FITTINGS, HOSE, HYDRAULIC, REUSABLE, FIELD-ATTACHABLE AND CLAMP-HALVES, TO MATE WITH SAE-J517 TYPE HOSES, GENERAL SPECIFICATION FOR |
| MS18196 Revision G:2016 | JACKSCREW, ELECTRICAL CONNECTOR, MALE AND FEMALE, FIXED |
| AWWA C509 : 2015 | RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE |
| ACI 301M : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
| ASTM F 2854 : 2010 : R2016 | Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing |
| MIL-DTL-17849 Revision F:2018 | Strainers, Sediment, Pipeline, Duplex (with and without Magnet) |
| MIL-DTL-24578 Revision C:2015 | Valves, Globe, Pressure Instrument, Stem Test Connection, Union End |
| MS27069 Revision H:2017 | SOCKET, HOSE COUPLING |
| MIL-DTL-24356 Revision B:2017 | Couplings and Split Clamps, 2½-, 4-, 6-, and 7-Inch Segmented, Reattachable, for Refueling-At-Sea Hose |
| ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| SAE J1086_201210 | Numbering Metals and Alloys |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM A 1058 : 2014 : REDLINE | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.