ASTM A 381 : 1996 : R2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission Systems
Hardcopy , PDF
01-05-2024
English
01-03-2012
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 01.01, 2017 Describes the straight seam, double-submerged-arc-welded steel pipe suitable for high-pressure service, 16 in. (406 mm) and larger in outside diameter, with wall thicknesses from 5/16 to 1[1/2] in. (7.9 to 38 mm).
| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
5
|
| ProductNote |
Reconfirmed 2012
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers straight seam, double-submerged-arc-welded steel pipe (Note 1) suitable for high-pressure service, 16 in. (406 mm) and larger in outside diameter, with wall thicknesses from 5/16to 11/2in. (7.9 to 38 mm). The pipe is intended for fabrication of fittings and accessories for compressor or pump-station piping. Pipe ordered to this specification shall be suitable for bending, flanging (vastoning), corrugating, and similar operations.
1.2Nine classes of pipe, based on minimum yield point requirements, are covered as indicated in Table 1.
| Class | Yield Strength, | Tensile Strength, | Elongation in 2 in. |
| Y 35 | 35000 (240) | 60000 (415) | 26 |
| Y 42 | 42000 (290) | 60000 (415) | 25 |
| Y 46 | 46000 (316) | 63000 (435) | 23 |
| Y 48 | 48000 (330) | 62000 (430) | 21 |
| Y 50 | 50000 (345) | 64000 (440) | 21 |
| Y 52 | 52000 (360) | 66000 (455) | 20 |
| Y 56 | 56000 (385) | 71000 (490) | 20 |
| Y 60 | 60000 (415) | 75000 (515) | 20 |
| Y 65 | 65000 (450) | 77000 (535) | 20 |
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4The following caveat applies to the test methods portion, Sections 9 and 10, only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ASME B36.10 : 1979 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
| ASTM E 30 : 1989 | Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron, and Wrought Iron (Withdrawn 1995) |
| ASTM A 530/A530M : 2012-06 | SPECIFICATION FOR GENERAL REQUIREMENTS FOR SPECIALIZED CARBON AND ALLOY STEEL PIPE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.