ASTM A 666 : 2023
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Hardcopy , PDF
12-04-2024
English
24-03-2023
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions for various structural, pressure vessel, magnetic, cryogenic, and heat-resisting applications.
1.2The application of this specification, or the use of material covered by this specification does not automatically allow usage in pressure vessel applications. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.
1.3The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 3110 : 2014 : R2018 | Standard Practice for Proper Use of Mechanical Trenchless Point Repair Sleeve with Locking Gear Mechanism for Pipes of Varying Inner Diameter and Offset Joints |
| ASTM F 2946 : 2012 : R2021 | Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes |
| ASTM F 2763/F2763M : 2016 : R2021 : EDT 1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2881/F2881M : 2021 : EDT 1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM D 1000 : 2017 | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 6195 : 2022 | Standard Test Methods for Loop Tack |
| ASTM D 7932 : 2017 | Standard Specification for Printed, Pressure-Sensitive Adhesive Labels for Use in Extreme Distribution Environments |
| ASTM F 2325 : 2014 : R2020 | Standard Classification for Multi-Layer Steel (MLS) and Other Metal Layer Gaskets for Transportation Applications |
| ASTM D 3815/D3815M : 2005 : R2019 | Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus |
| ASTM D 3330/D3330M : 2004 : R2018 | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape |
| ASTM D 3654/D3654M : 2006 : R2019 | Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes |
| ASTM F 2510/F2510M : 2022 | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes |
| ASTM F 1910 : 1998 : R2022 | Standard Specification for Long Barbed Tape Obstacles |
| ASTM F 1267 : 2018 | Standard Specification for Metal, Expanded, Steel |
| ASTM D 6551/D6551M : 2005 : R2019 | Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus |
| ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM D 6463/D6463M : 2006 : R2020 | Standard Test Method for Time to Failure of Pressure Sensitive Articles Under Sustained Shear Loading |
| ASTM F 2332 : 2006 : R2022 | Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components |
| ASTM C 1802 : 2020 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM D 6252/D6252M : 1998 : R2019 | Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle |
| ASTM F 2947/F2947M : 2021 : REV A | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM A 480/A480M : 2022 : REV A | Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| NAAMM HMMA 862:2023 | Guide Specifications For Forced Entry/Bullet Resistant (FE/BR) Security Hollow Metal Doors and Frames |
| ASTM C 1478/C1478M : 2020 | Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals |
| ASTM C 1802 : 2023 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM C 923/C923M : 2020 | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals |
| ASTM F 3110 : 2014 : R2024 | Standard Practice for Proper Use of Mechanical Trenchless Point Repair Sleeve with Locking Gear Mechanism for Pipes of Varying Inner Diameter and Offset Joints |
| ASTM D 7932 : 2017 : R2023 | Standard Specification for Printed, Pressure-Sensitive Adhesive Labels for Use in Extreme Distribution Environments |
| ASTM F 2764/F2764M : 2023 | Standard Specification for 6 in. to 60 in. [150 mm to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM F 1267 : 2018 : R2023 | Standard Specification for Metal, Expanded, Steel |
| ASTM A 484/A484M : 2023 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM A 480/A480M : 2023 : REV B | Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| ASTM A 941 : 2023 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 480/A480M : 2023 : REV A | Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| ASTM E 527 : 2023 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM A 240/A240M : 2022 : REV B | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM E 527 : 2016 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM A 240/A240M : 2023 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2022 : REV A | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 484/A484M : 2022 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM A 484/A484M : 2024 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings |
| ASTM A 941 : 2024 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 480/A480M : 2023 | Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| ASTM A 484/A484M : 2023 : REV A | Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings |
| ASTM A 240/A240M : 2023 : REV A | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 480/A480M : 2022 : REV A | Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| ASTM A 370 : 2024 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.