Credit card payment only is accepted for this order because it contains a mix of both publications and training products.
Invalid username/password. Please try again.
xyz
Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
:
Available format(s): Hardcopy, PDF
Language(s): English
Published date: 01-07-2017
Publisher: American Society for Testing and Materials
These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows: Class 1—Non-elastomeric backings made from materials such as: Paper, flat or creped.
1.1These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows:
1.1.1Class 1—Non-elastomeric backings made from materials such as:
Paper, flat or creped,
Fabric, uncoated or coated,
Cellulose ester films,
Polyethylene terephthalate (polyester) films,
Fluorocarbon polymer films,
Composite filament films,
Polyamide films,
Polyimide films, and
Combinations thereof.
1.1.2Class 2—Elastomeric backings that are characterized by both high stretch and substantial recovery. These backings are made from materials such as:
Vinyl chloride and co-polymers,
Vinylidene chloride and co-polymers, and
Polyethylene and co-polymers.
1.2Test laminates of Class 1 and Class 2 backings according to Class 1 test methods.
1.3The procedures appear in the sections indicated below and in alphabetical order:
Adhesion Strength to Steel and Backing at Room Temperature
46 – 53
Adhesion Strength to Steel and Backing at Low Temperatures
Bond Strength After Solvent Immersion
110 – 115
Breaking Strength and Elongation at Room Temperature
37 – 45
Breaking Strength and Elongation at Low Temperatures
Conditioning
6 – 8
Curling and Twisting
140 – 146
Dielectric Breakdown Voltage
83 – 90
Effect of Accelerated Aging on High-Temperature Tapes
97 – 103
Flagging
66 – 76
Flammability
104 – 109
Hazards/Precautions
3
Insulation Resistance at High Humidity
91 – 96
Length of Tape in a Roll
28 – 36
Oil Resistance
116 – 122
Puncture Resistance
123 – 128
Resistance to Accelerated Aging (Heat and Moisture)
129 – 139
Sampling
4
Specimen Preparation
5
Thermosetting Properties
77 – 82
Thickness
21 – 27
Unwind Force at Room Temperature
54 – 65
Unwind Force at Low Temperatures
Width
11 – 20
Note 1:These procedures apply to both Class 1 and Class 2 tapes except as noted above.
1.4This is a fire-test response standard (see Section 104).
1.5The values stated in SI units are the standard, unless otherwise noted. If a value for measurement is followed by a value in inch-pound or English units in parentheses, it is likely that the second value will only be approximate and it is for information only. The first stated value is the preferred unit.
Note 2:These test methods are similar to IEC 60454–3, but may differ sometimes in some details.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 3.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
AUD CAD CHF CNY DKK EUR GBP HKD IDR INR JPY KRW MXN NOK NZD SEK SGD USD ZAR
Unfortunately, this product is not available for purchase in your region.
Features
Get in touch with us
Loading..
A free alerting service to track changes to standards.
Once you've completed your purchase you'll get a link to My Orders on: -the Confirmation page of check out -and by email You'll be able to access your Multi User Orders to add Users.
You have selected more than three (3) participants. Please contact our Customer Service team.
You have already added this product in the cart. If you would like to add additional copies of this product please adjust the Quantity in the cart. For more than 10 copies, please contact our Customer Support team on +353 (0)1 857 6730.
You have selected more than three (3) trainings. Please contact our Customer Service team.Please contact our Customer Service team on Email: sales@saiglobal.com Phone: 131 242 (Within Australia)
You have already added a product with different Currency. Please change the currency.
This product cannot be added to your cart right now. Please contact our Customer Service team on Email: info@standards.iePhone: +353(0)1 857 6730
You have already saved 6 Quotes. Please contact our Customer Service Team.