ASTM A 815/A815M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping Fittings
Hardcopy , PDF
11-09-2017
English
01-09-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction covered by the latest revision of Specification A960/A960M. Fittings differing from these standards may be furnished in accordance with Supplementary Requirement S58 of Specification A960/A960M.
1.1.1Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. They are manufactured to the requirements of Specification A960/A960M, and they shall have pressure ratings compatible with 13.2. Class WP-S fittings are those manufactured from seamless product by a seamless method of manufacture (marked with class symbol WP-S); Class WP-W fittings are those which contain welds where the fitting fabrication or construction welds have been radiographed (marked with class symbol WP-W); and Class WP-WX fittings are those which contain welds where all welds have been radiographed (marked with class symbol WP-WX); and Class WP-WU fittings are those which contain welds where all welds have been ultrasonically tested (marked with class symbol WP-WU).
1.1.2Class CR fittings are those manufactured to the requirements of MSS SP-43, and they shall have pressure ratings compatible with 13.3.
1.2This specification does not apply to cast fittings.
1.3Optional supplementary requirements are provided. When desired, one or more of these may be specified in the order.
1.4This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units.
1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| MSS SP 97 : 2012 | INTEGRALLY REINFORCED FORGED BRANCH OUTLET FITTINGS - SOCKET WELDING, THREADED, AND BUTTWELDING ENDS |
| NFPA 750 : 2015 | WATER MIST FIRE PROTECTION SYSTEMS |
| ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
| ASME B16.9 : 2012 | FACTORY-MADE WROUGHT BUTTWELDING FITTINGS |
| UNI EN ISO 13628-15 : 2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 15: SUBSEA STRUCTURES AND MANIFOLDS |
| BS EN ISO 13628-15:2011 | Petroleum and natural gas industries. Design and operation of subsea production systems Subsea structures and manifolds |
| NSF 61 : 2017 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| ASME B31.1 : 2016 | POWER PIPING |
| ASME B31.3:2016 | PROCESS PIPING |
| AWWA C226 : 2013 | STAINLESS-STEEL FITTINGS FOR WATERWORKS SERVICE, SIZES 1/2 IN. THROUGH 72 IN. (13 MM THROUGH 1,800 MM) |
| FM 5580 : 2012 | HYBRID (WATER AND INERT GAS) FIRE EXTINGUISHING SYSTEMS |
| MSS SP 95 : 2014 | SWAGE(D) NIPPLES AND BULL PLUGS |
| API 17P : 2013 | DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - SUBSEA STRUCTURES AND MANIFOLDS |
| ISO 13628-15:2011 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 15: Subsea structures and manifolds |
| EN ISO 13628-15:2011 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures and manifolds (ISO 13628-15:2011) |
| I.S. EN ISO 13628-15:2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 15: SUBSEA STRUCTURES AND MANIFOLDS (ISO 13628-15:2011) |
| ASME B31.3 SPANISH : 2010 | PROCESS PIPING |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.