ASTM B 386/B386M : 2019 : EDT 1
Current
The latest, up-to-date edition.
Standard Specification for Molybdenum and Molybdenum Alloy Plate,Sheet, Strip, Foil, and Ribbon
Hardcopy , PDF
English
01-01-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
B 10
|
| DocumentType |
Standard
|
| Pages |
6
|
| ProductNote |
ε1 NOTE—An editorial correction was made to Table 4 in January 2020.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers unalloyed molybdenum and molybdenum alloy plate, sheet, strip, foil, and ribbon as follows:
1.1.1Molybdenum 360—Unalloyed vacuum arc-cast molybdenum.
1.1.2Molybdenum 361—Unalloyed powder metallurgy molybdenum.
1.1.3Molybdenum Alloy 363—Vacuum arc-cast molybdenum-0.5 % titanium-0.1 % zirconium (TZM) alloy.
1.1.4Molybdenum Alloy 364—Powder metallurgy molybdenum-0.5 % titanium-0.1 % zirconium (TZM) alloy.
1.1.5Molybdenum 365—Unalloyed vacuum arc-cast molybdenum, low carbon.
1.1.6Molybdenum Alloy 366—Vacuum arc-cast molybdenum-30 % tungsten alloy.
1.1.7Drawing Grade—A drawing grade is defined, which may be specified as a separate requirement by the purchaser.
1.2Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.2.1The ball punch deformation test called for in 8.4 is a test that is specified in the inch-pound system, and original test results used to produce Fig. 2 were all obtained using inch-pound measurements. For this reason, the graph of minimum required cup height as a function of sheet thickness has been retained in its original inch-pound system. The graphical data has been scanned and a straight line fitted to the scan data. The equation of this line is included in both inch-pound and SI units.
1.3The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 1941 : 2010 : R2016 | Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys by Combustion Analysis |
| ASTM E 1941 : 2010 : R2024 | Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys by Combustion Analysis |
| ASTM E 92 : 2023 | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
| ASTM E 643 : 2024 | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 384 : 2022 | Standard Test Method for Microindentation Hardness of Materials |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 643 : 2015 | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material |
| ASTM E 345 : 2016 | Standard Test Methods of Tension Testing of Metallic Foil |
| ASTM E 345 : 2024 | Standard Test Methods of Tension Testing of Metallic Foil |
| ASTM E 384 : 2011 | Standard Test Method for Knoop and Vickers Hardness of Materials |
| ASTM E 92 : 2017 | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
| ASTM E 345 : 2024 : REV A | Standard Test Methods of Tension Testing of Metallic Foil |
| ASTM E 92 : 1982 : R2003 : EDT 2 | Standard Test Method for Vickers Hardness of Metallic Materials (Withdrawn 2010) |
| ASTM E 384 : 2017 | Standard Test Method for Microindentation Hardness of Materials |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.