ASTM B 660 : 2015 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
Available format(s)
PDF
Superseded date
05-11-2021
Superseded by
Language(s)
English
Published date
01-05-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 02.02, 2015 Specifies methods of packaging/packing aluminum and magnesium products, in preparation for storage or shipment, both foreign and domestic.
| Committee |
B 07
|
| DocumentType |
Redline
|
| Pages |
29
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These practices describe methods of packaging/packing aluminum and magnesium products, in preparation for storage or shipment, both foreign and domestic. Assuming proper and normal handling in transit, these practices are designed to deliver the products to their destination in good condition. For DoD redistribution, see Supplementary Requirements.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3Aluminum and magnesium products must be preserved and packed so as to be adequately protected from possible damage during shipment and storage. Major damage types are:
1.3.1Mechanical, including bending, crushing, denting, scratching, or gouging during handling and storage; and abrasions resulting from vibration during transport of the material.
1.3.2Corrosion, or water stain, resulting from exposure of packed material to water, either externally applied, or as condensate caused by temperature variations in a humid atmosphere.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| SAE AMS4028H | Aluminum Alloy Sheet and Plate 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-O) Annealed |
| ASTM B 91 : 2017 : REDLINE | Standard Specification for Magnesium-Alloy Forgings |
| SAE AMS4140K | Aluminum Alloy Die Forgings 4.0Cu - 2.0Ni - 0.68Mg (2018-T61) Solution and Precipitation Heat Treated |
| SAE AMS4069F | Aluminum Alloy, Drawn, Round Seamless Tubing Close Tolerance 2.5Mg - 0.25Cr (5052-O) Annealed |
| SAE AMS4863 | Copper-Nickel-Tin Alloy Castings Cu – 15Ni – 8Sn Hot Isostatically Pressed, Solution Annealed and Spinodal Heat Treated |
| SAE AMS4458A | Aluminum Alloy, Plate (2.7 Cu - 1.8 Li - 0.7 Zn) 2099-T86 Solution Heat Treated, Cold Worked and Artificially Aged |
| ASTM B 93/B93M : 2015 : REDLINE | Standard Specification for Magnesium Alloys in Ingot Form for Sand Castings, Permanent Mold Castings, and Die Castings |
| SAE AMS4272 | Aluminum Alloy, Alclad Sheet and Plate (Alclad 2029-T8) 3.6 Cu, 0.30 Mn, 0.95 Mg, 0.40 Ag, 0.12 Zr Solution Heat Treated, Cold Worked and Aged |
| ASTM B 199 : 2017 : REDLINE | Standard Specification for Magnesium-Alloy Permanent Mold Castings |
| ASTM B 317/B317M : 2007 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 236 : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 234M : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
| SAE AMS4466A | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T361 Sheet & Plate) Solution Heat Treated, 6% Cold Worked and Naturally Aged |
| SAE AMS4405A | Aluminum Alloy, Alclad Sheet (6156-T4) 1.0Si - 0.90Cu - 0.60Mn - 0.90Mg Solution Heat Treated and Naturally Aged |
| SAE AMS4332 | Aluminum Alloy, Extruded Profiles (7349-T76511) 8.1Zn - 1.7Cu - 2.2Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4306C | Aluminum Alloy, Plate 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T6151) Solution Heat Treated, Stress Relieved, and Aged |
| SAE AMS4083L | Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4401 : 2011 | ALUMINUM ALLOY PLATE (7140-T7451), 6.6ZN - 1.8CU - 2.0MG - 0.10ZR, SOLUTION HEAT TREATED, STRESS RELIEVED AND OVERAGED (COMPOSITION SIMILAR TO UNS A97140) |
| SAE AMS4126C | Aluminum Alloy, Die and Hand Forgings and Rolled Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6) Solution and Precipitation Heat Treated |
| SAE AMS4182H | Aluminum Alloy, Wire 5.0Mg - 0.12Mn - 0.12Cr (5056-O) Annealed |
| SAE AMS4081J | Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4044N | Aluminum Alloy, Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr Annealed (7075-O) or when specified, “As Fabricated” (7075-F) |
| SAE AMS4096D | Aluminum Alloy Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (Alclad 2219-O) Annealed |
| SAE AMS4184G | Filler Metal, Aluminum Brazing 10Si - 4.0Cu (4145) |
| SAE MAM4131B | Aluminum Alloy, Die and Hand Forgings 5.6zn 2.5mg 1.6cu 0.23cr Solution Heat Treated and Aged |
| SAE AMS4465A | Aluminum Alloy, Clad One Side Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 23 Brazing Sheet) As Fabricated |
| MIL-S-52836 Revision A:1974 | SUPPLEMENTARY SET, BRIDGE, TROOP SUPPORT, PACKAGING OF |
| SAE AMS4046G | Aluminum Alloy Sheet and Plate, Alclad One Side 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad One Side 7075; -T6 Sheet -T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4013G | Aluminum Sheet, Laminated Surface Bonded |
| SAE AMS4312D | Aluminum Alloy, Rolled or Forged Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T651, 6061-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated |
| SAE AMS 4203 : 2012 | ALUMINUM ALLOY, PLATE, 6.2ZN - 1.8CU - 2.4MG - 0.13ZR (7010-T7351) SOLUTION HEAT TREATED, STRESS RELIEVED AND PRECIPITATION HEAT TREATED (COMPOSITION SIMILAR TO UNS A97010) |
| SAE AMS4141G | Aluminum Alloy Die Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73) Solution and Precipitation Heat Treated |
| SAE AMS4409 | Aluminum Alloy, Plate 4.0Zn - 2.0Mg - 0.32Mn (7019-T651) Solution Heat Treated, Stress Relieved and Artificially Aged |
| SAE AMS4290M | Aluminum Alloy, Die Castings 9.5Si - 0.50Mg (360.0-F) As Cast |
| SAE AMS4490K | Magnesium Alloy Castings, Die 9.0Al - 0.70Zn (AZ91D, Temper F) As Cast |
| SAE AMS4064F | Aluminum Alloy, Clad Two Sides Sheet 1.25Mn - 0.12Cu (No. 12-0 Brazing Sheet) Annealed |
| QQ-A-225 Revision G:1990 | ALUMINUM AND ALUMINUM ALLOY BAR, ROD, WIRE, OR SPECIAL SHAPES, ROLLED, DRAWN, OR COLD FINISHED, GENERAL SPECIFICATION FOR |
| SAE AMSB20148C | Brazing Sheet, Aluminum Alloy |
| ASTM B 928 : 2004 | Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service |
| SAE AMS4321B | Aluminum Alloy Forgings 7.7Zn - 2.5Mg - 1.5Cu - 0.16Cr (7049-01) High Temperature Annealed |
| SAE AMS4324A | Aluminum Alloy, Extruded Rod, Bar and Profiles (7055-T74511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4362G | Forgings, Magnesium Alloy 5.5Zn - 0.45Zr (ZK60A-T5) Precipitation Heat Treated |
| SAE AMS4330C | Aluminum Alloy, Plate (2297-T87) 2.8Cu - 1.5Li - 0.30Mn - 0.12Zr Solution Heat Treated, Stretched, and Artificially Aged |
| SAE AMS4416B | Aluminum Alloy, Extruded Profiles (2196-T8511) 2.9Cu - 1.7Li - 0.4Mg - 0.4Ag - 0.10Zr Solution Heat Treated, Stress Relieved by Stretching and Artificially Aged |
| SAE AMS4077H | Aluminum Alloy Sheet and Plate, Alclad One Side 4.4Cu - 1.5Mg - 0.60Mn (Clad One Side 2024-O) Annealed |
| SAE AMS4276B | Aluminum Alloy, Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-O) Annealed, Fine Grained |
| SAE AMS 4473 : 2017 | ALUMINUM ALLOY PLATE (2624-T39), 4.1CU - 1.4MG - 0.6MN, SOLUTION HEAT TREATED, COLD WORKED AND NATURALLY AGED |
| SAE AMS4462A | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T3 Sheet, -T351 Plate) Solution Heat Treated, Cold Worked and Naturally Aged |
| SAE AMS4015M | Aluminum Alloy, Sheet and Plate 2.5Mg - 0.25Cr (5052-O) Annealed |
| SAE AMS4162E | Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T8511) Solution Treated, Stress Relief Stretched, Straightened, and Precipitation Heat Treated |
| SAE AMS4365 | Aluminum Alloy, Plate, 7.9Zn – 1.2Cu - 2.1Mg - 0.10Zr (7097-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4133E | Aluminum Alloy Forgings and Rolled Rings 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6) Solution and Precipitation Heat Treated |
| SAE AMS4304B | Aluminum Alloy, Discontinuously Reinforced Sheet 2009/SiC/15w (T8P) Solution Heat Treated, Stretched, and Precipitation Heat Treated |
| SAE AMS4300D | Boron-Aluminum Composite Sheet 50 v/o 5.6B, 6061-0, For Diffusion Bonding |
| SAE AMS4344D | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged |
| SAE AMS4318A | Aluminum Alloy, Rolled or Cold Finished Bars and Rods, 12.2Si - 1.0Mg - 0.90Cu - 0.90Ni (4032-T86) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4131D | Aluminum Alloy, Die and Hand Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T74) Solution Heat Treated and Aged |
| SAE AMS4217J | Aluminum Alloy, Castings 7.0Si - 0.32Mg (356.0-T6) Solution and Precipitation Heat Treated |
| SAE AMSQQA367E | Aluminum Alloy Forgings |
| SAE AMS4353 | Aluminum Alloy, Extruded Round Rod 3.5Cu - 1.0Li - 0.40Mg - 0.45Ag - 0.12Zr (2050-T84) Solution Heat Treated, Stress Relieved by Stretching, and Artificially Aged |
| SAE AMS4049M | Aluminum Alloy, Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet - T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4601A | Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr Solution Heat Treated, Cold Worked and Naturally Aged (2219 -T31/-T351) |
| SAE AMS4213A | Aluminum Alloy Plate (2027-T351) 4.4Cu - 1.2Mg - 0.8Mn - 0.10Zr Solution Heat Treated, Cold Worked and Naturally Aged |
| SAE AMS 4483 : 2013 | MAGNESIUM ALLOY CASTINGS, PERMANENT MOLD, 10AL (AM100A-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS4459A | Aluminum Alloy, Extrusion 2.7Cu - 1.8Li - 0.7Zn - 0.3Mn - 0.3Mg - 0.08Zr (2099-T81) Solution Heat Treated, Stress Relieved by Stretching 1 to 3% and Aged |
| SAE AMS4280J | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.5Mg (355.0-T71) Solution Heat Treated and Overaged |
| SAE AMS4009C | Aluminum Alloy Foil 1.0Mg - 0.6Si - 0.30Cu - 0.20Cr (6061-0) Annealed |
| ASTM B 317/B317M : 2007 : R2015 : EDT 1 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| SAE AMS4287A | Aluminum Alloy, Extrusion 2.7Cu - 1.8Li - 0.7Zn - 0.3Mn - 0.3Mg - 0.08Zr (2099-T83) Solution Heat Treated, Stress Relieved by Stretching 1% to 4% and Aged |
| ASTM B 491/B491M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications |
| SAE AMS QQ A 200 : 2004 | ALUMINUM ALLOY, BAR, ROD, SHAPES, STRUCTURAL SHAPES, TUBE, AND WIRE, EXTRUDED: GENERAL SPECIFICATION FOR |
| ASTM B 317/B317M : 2007 : R2015 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| SAE AMS4468 | Aluminum Alloy, Plate 5.0Cu - 0.4Mn - 0.5Mg - 0.4Ag (2139-T84) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4021H | Aluminum Alloy, Alclad Sheet and Plate, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (Alclad 6061-0) Annealed |
| ASTM B 928/B928M : 2015 : REDLINE | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| SAE AMS4164H | Aluminum Alloy, Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3510) Stress-Relief Stretched, Unstraightened |
| SAE AMS4035M | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024-O) Annealed; or when specified, “As Fabricated” (2024-F) |
| SAE AMS4113F | Aluminum Alloy, Extruded Profiles 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4472 : 2017 | ALUMINUM ALLOY, PLATE, 4.0CU - 1.0LI - 0.40MG - 0.35AG - 0.13ZR (2195-T34), SOLUTION HEAT TREATED AND STRESS RELIEVED |
| ASTM B 209M : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) |
| SAE AMS4066C | Aluminum Alloy, Drawn, Round Seamless Tubing 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti - (2219-T8511) Solution Heat Treated, Stress Relieved by Stretching and Precipitation Heat Treated |
| SAE AMS4116J | Aluminum Alloy, Bars, Rods, and Wire 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T4) Cold Finished, Solution Heat Treated and Naturally Aged |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| SAE AMS4172F | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4511 or T4510) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4477A | Aluminum Alloy, Coiled Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-T4) Solution Treated |
| SAE AMS4194E | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024 -T361 Sheet/Plate with 1½% Alclad) Solution Heat Treated, 6% Cold Worked and Naturally Aged |
| ASTM B 247M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric) |
| SAE AMS4256C | Aluminum Alloy, Clad Two Sides Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 22 Brazing Sheet) As Fabricated |
| SAE AMS4269A | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn; (2024-T361), Solution Heat Treated and Cold Worked |
| SAE AMS4341E | Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged |
| SAE AMS4100F | Aluminum Alloy, Alclad, Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (Alclad 7475-T761) Solution and Precipitation Heat Treated |
| SAE AMS4254C | Aluminum Alloy, Aramid Fiber Reinforced, Laminated Sheet 4.4Cu - 1.5Mg - 0.6Mn (2024-T3) 3, 5, 7, or 9 Ply |
| SAE AMS4296C | Aluminum Alloy, Alclad Sheet and Plate 4.3Cu - 1.4Mg - 0.60Mn (Alclad 2524-T3) Solution Heat Treated and Cold Worked |
| MIL-A-12545 Revision D:1989 | ALUMINUM ALLOY IMPACTS |
| SAE MAM4427A | Magnesium Alloy Sand Castings 4.0y 2.3nd 0.7zr Solution and Precipitation Heat Treated |
| SAE AMS4476 | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-O) Annealed |
| SAE AMS4406A | Aluminum Alloy, Centrifugal Castings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (709.0-T61) Hot Isostatically Pressed, Solution and Precipitation Heat Treated |
| SAE AMS4153L | Aluminum Alloy, Extrusions 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6) Solution and Precipitation Heat Treated |
| SAE AMS4361 | Aluminum Alloy, Plate (7065-T7451) 7.7Zn - 2.1Cu - 1.65Mg - 0.10Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4128D | Aluminum Alloy Bars, Rolled or Cold Finished 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4469 | Aluminum Alloy Tubing, Seamless, Drawn 1.8 Cu - 1.0 Mg - 0.8 Si - 0.20 Cr Solution Heat Treated, Stress-Relieved by Stretching, and Aged (2013-T4511) |
| SAE AMS4420P | Magnesium Alloy Castings, Sand 6Al - 3Zn (AZ63A-F) As Cast |
| SAE AMS4617A | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73, 7075-T73511, 7075-T73510) Solution Heat Treated, Stress Relieved by Stretching when required, and Overaged |
| SAE AMS4411 | Aluminum Alloy Plate (7081-T7651) 7.2Zn - 1.5Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged |
| SAE AMS4208C | Aluminum Alloy Sheet 6.0Cu - 0.40Zr - (2004-F) As Rolled |
| SAE AMS4227E | Aluminum Alloy, Castings, Sand, 8.0cu 6.0mg 0.50mn 0.50ni, as Cast |
| SAE AMS4121J | Aluminum Alloy Bars, Rods, and Wire, Rolled, Drawn, or Cold Finished 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6, -T651) Solution and Precipitation Heat Treated |
| SAE AMS4048P | Aluminum Alloy Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075-O) Annealed or when specified, “As Fabricated” (Alclad 7075-F) |
| SAE AMS4050J | Aluminum Alloy, Plate 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7451) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4202D | Aluminum Alloy Plate 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T7351) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated |
| SAE AMS4298A | Aluminum Alloy, Alclad Sheet 3.8Cu – 1.0Mg – 0.30Mn – 0.60Zn (Alclad 2056-T3) Solution Heat Treated and Cold Worked |
| SAE AMS4216B | Aluminum Alloy, Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.50Mn (6013-T6) Solution Heat Treated and Artificially Aged |
| SAE AMS4357 | Aluminum Alloy, Die Forgings 3.5Cu – 1.0Li - 0.04Mg – 0.35Mn – 0.45Ag – 0.12Zr (2050-T852) Solution Heat Treated, Cold Worked and Artificially Aged |
| SAE AMS4266B | Aluminum Alloy, Sheet 6.5Fe - 1.3Si - 0.60V (8022-H112) Powder Metallurgy Product, Strain Hardened |
| SAE AMS4146G | Aluminum Alloy Forgings and Rolled or Forged Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061 - T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4464A | Aluminum Alloy Plate (2624-T351) 4.1Cu - 1.4Mg - 0.6Mn Solution Heat Treated, Cold Worked and Naturally Aged |
| SAE AMS4268A | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn; (2024-T81 Sheet, -T851 Plate) Solution Heat Treated, Cold Worked and Artificially Aged |
| SAE AMS4329B | Aluminum Alloy, Plate (7085-T7651) 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4036L | Aluminum Alloy Sheet and Plate, Alclad One Side 4.4Cu - 1.5Mg - 0.60Mn Alclad One Side 2024 and 1-1/2% Alclad One Side 2024-T3 Sheet; 1-1/2% Alclad One Side 2024-T351 Plate |
| SAE AMS4204C | Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T7651) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4143E | Aluminum Alloy Forgings and Rolled or Forged Rings 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T6) Solution and Precipitation Heat Treated |
| SAE AMS4429A | Magnesium Alloy Castings, Sand 2.8Nd - 1.4Gd - 0.4Zn - 0.6Zr (EV31A - T6) Solution and Precipitation Heat Treated |
| ASTM B 107/B107M : 2013 : REDLINE | Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| SAE AMS4285F | Aluminum Alloy Castings, Centrifugal 7.0Si - 0.30Mg (356.0-T6) Solution and Precipitation Heat Treated |
| ASTM B 211M : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) (Withdrawn 2019) |
| ASTM B 85 : 2003 | Standard Specification for Aluminum-Alloy Die Castings |
| ASTM B 80 : 2015 : REDLINE | Standard Specification for Magnesium-Alloy Sand Castings |
| ASTM B 211 : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| SAE AMS4319B | Aluminum Alloy, Rolled or Cold Finished, Bars and Rods 12.2Si - 1.0Mg - 0.90Cu - 0.90Ni (4032-T651) Solution Heat Treated, Stress-Relieved, and Artificially Aged |
| ASTM B 236M : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) [Metric] |
| SAE AMS4403A | Aluminum Alloy, Die Forgings 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr (7085-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged |
| SAE AMS4410 | Aluminum Alloy Plate (7081-T7451) 7.2Zn - 1.5Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged |
| ASTM B 403 : 2012 : REDLINE | Standard Specification for Magnesium-Alloy Investment Castings |
| ASTM B 483/B483M : 2013 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications |
| SAE AMS4310E | Aluminum Alloy, Rolled or Forged Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T651, 7075-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4249A | Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated (Requiring Fatigue and Fracture Toughness Testing) |
| SAE MAM4208B | Aluminum Alloy, Sheet, 6.0cu 0.40zr, as Rolled |
| SAE AMS4223E | Aluminum Alloy, Castings 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4115J | Aluminum Alloy, Rolled or Cold-Finished, Bars, Rods, Wire, and Flash Welded Rings Annealed 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) |
| SAE AMS4235C | Aluminum Alloy Castings 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T7) Solution and Precipitation Heat Treated |
| SAE AMS4314D | Aluminum Alloy Rings, Rolled or Forged 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T651, 2014-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4078J | Aluminum Alloy Sheet and Plate 5.6Zn – 2.5Mg-1.6Cu-0.23Cr 7075: (-T73 Sheet, -T7351 Plate) Solution Heat Treated and Overaged |
| SAE AMS4424L | Magnesium Alloy Castings, Sand 6.0Al - 3.0Zn (AZ63-T6) Solution and Precipitation Heat Treated |
| SAE AMS4258B | Laminated Sheet, Aluminum Alloy, Aramid Fiber Reinforced 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (Alclad, One Side 7475-T761) 5 or 7 Ply |
| SAE AMS4259B | Aluminum Alloy, Sheet 2.4Li - 1.3Cu - 0.95Mg - 0.10Zr (8090-T6) Solution and Precipitation Heat Treated (Unrecrystallized) |
| SAE AMS4418H | Magnesium Alloy, Sand Castings 2.5Ag - 2.1Di - 0.70Zr (QE22A-T6) Solution and Precipitation Heat Treated |
| SAE AMSA21180C | Aluminum-Alloy Castings, High Strength |
| ASTM B 211 : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| SAE AMS4278B | Aluminum Alloy, Alclad Sheet 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075-0) Annealed, Fine Grained |
| MIL-C-9897 Revision C:1992 | CRATE, SLOTTED ANGLE, STEEL OR ALUMINUM FOR LIGHTWEIGHT AIRFRAME COMPONENTS AND BULKY ITEMS [FOR MAXIMUM LOADS OF 3000 POUNDS] |
| MIL-P-63514 Revision A:1986 | PROJECTILE, 105MM, TP-T, M489A1, METAL PARTS ASSEMBLY |
| SAE AMS4325 | Aluminum Alloy, Extruded Wide Panel Profiles (7150-T77511) 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr Solution Heat Treated, Stress-Relieved, Straightened and Overaged |
| SAE AMS4200C | Aluminum Alloy Plate 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T7351) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4277B | Aluminum Alloy, Sheet 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-O) Annealed, Fine Grained |
| SAE AMS4412A | Aluminum Alloy, Sheet 3.2Cu - 0.52Mg - 0.30Ag - 0.12Zr (2198-T8) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4339B | Aluminum Alloy, Rolled or Cold Finished Bars and Rods 4.4Cu - 1.5Mg - 0.60Mn (2024-T851) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4343D | Aluminum Alloy, Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7149-T73511) Solution Heat Treated, Stress Relieved by Stretching, and Overaged |
| SAE AMS4154R | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6, 7075-T6510, 7075-T6511) Solution Heat Treated, Stress Relieved by Stretching when Required and Precipitation Heat Treated |
| SAE AMS4252B | Aluminum Alloy, Plate 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T7751) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4079H | Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Close Tolerance, Annealed |
| SAE AMS4186D | Aluminum Alloy Bars, Rods, and Wire, Rolled or Cold Finished 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-F) As Fabricated, or when specified, Annealed (7075-O) |
| SAE AMS4193D | Aluminum Alloy Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024-T861) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| SAE AMS4293 | Aluminum Alloy Extrusions 7.9Zn - 1.6Cu - 2.2Mg - 0.16Cr (7249-T76511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged |
| SAE AMS4183A | Aluminum Alloy, Extruded Profiles (2027-T3511) 4.4Cu - 1.2Mg - 0.8Mn - 0.10Zr Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS 5731 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1800 DEGREES F (982 DEGREES C) SOLUTION HEAT TREATED |
| SAE AMS4090F | Aluminum Alloy, Plate 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T651) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4094D | Aluminum Alloy, Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T81 Sheet Solution Heat Treated, Cold Worked, and Precipitation Heat Treated Alclad 2219-T851 Plate Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4209C | Aluminum Alloy Sheet, Alclad 6.0Cu - 0.40Zr - (2004-F) As Rolled |
| SAE AMS4368 | Aluminum Alloy, Discontinuously Reinforced Hot Isostatically Pressed Shapes 6061B/SiC/40p (3μm) (T1P) |
| SAE AMS4331 | Aluminum Alloy Extrusions 7.8Zn - 2.6Mg - 2.0Cu - 0.10Zr - (7068-T6511) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4291J | Aluminum Alloy, Die Castings 8.5Si - 3.5Cu (A380.0-F) As Cast |
| SAE AMS4070N | Aluminum Alloy, Drawn, Round Seamless Tubing 2.5Mg - 0.25Cr (5052-O) Annealed |
| SAE AMS4027N | Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4160H | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Annealed |
| SAE AMS4251B | Aluminum Alloy Sheet 2.7Cu - 2.2Li - 0.12Zr (2090-T83) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| SAE AMS4225E | Aluminum Alloy, Heat-Resistant, Castings 5.0Cu - 1.5Ni - 0.25Mn - 0.25Sb - 0.25Co - 0.20Ti - 0.20Zr (203.0-T6) Solution Heat Treated and Precipitation Heat Treated |
| SAE AMS4045L | Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4334B | Aluminum Alloy, Forgings 7.8Zn - 2.2Mg - 1.6Cu - 0.15Cr (7249-T74 and -T7452) |
| SAE AMS4479 | Aluminum Alloy, Extruded Profiles (2824-T3511) 4.0Cu - 1.35Mg - 0.7Mn Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4463A | Aluminum Alloy, Plate (7255-T7751) 8.0Zn - 2.3Cu - 2.0Mg - 0.12Zr Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4374 | Aluminum Alloy, Extruded Profiles 8.9Zn - 2.2Cu - 2.2Mg - 0.15Zr (7136-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged |
| SAE AMS4408A | Aluminum Alloy, Plate (7140-T7651) 6.6Zn - 1.8Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4084E | Aluminum Alloy Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T61) Solution and Precipitation Heat Treated |
| SAE AMS4026M | Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T4 Sheet, -T451 Plate) Solution Heat Treated and Naturally Aged |
| SAE AMS4212L | Aluminum Alloy Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4101F | Aluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T851) Solution Heat Treated, Stretched, and Precipitation Heat Treated |
| SAE AMS4017L | Aluminum Alloy Sheet and Plate 2.5Mg - 0.25Cr (5052-H34) Strain-Hardened, Half-Hard, and Stabilized |
| SAE MAM4323B | Aluminum Alloy, Hand Forgings, 5.6zn 2.5mg 1.6cu 0.23cr, Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4417C | Castings, Sand, Magnesium Alloy 1.5Ag - 2.1Di - 0.08Cu - 0.70Zr (EQ21A - T6) Solution and Precipitation Heat Treated |
| SAE AMS5632J | Steel, Corrosion-Resistant, Bars, Wire, and Forgings 17Cr - 0.50Mo (0.95 - 1.20C) (440F) Free-Machining, Annealed |
| SAE AMS4130N | Aluminum Alloy Die Forgings 4.4Cu - 0.85Si - 0.80Mn (2025-T6) Solution and Precipitation Heat Treated |
| SAE AMS2670J | Brazing, Copper |
| SAE AMS4415A | Aluminum Alloy Extrusions 8.9Zn - 2.2Cu - 2.2Mg - 0.15Zr (7136-T76511, -T76510) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged |
| ASTM B 90M : 1990 | Specification for Magnesium-Alloy Sheet and Plate (Metric) (Withdrawn 1993) |
| SAE AMS4157E | Aluminum Alloy Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T73511) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4327A | Aluminum Alloy, Plate (2098-O) 3.5Cu - 1.1Li - 0.50Mg - 0.40Ag - 0.11Zr Annealed |
| SAE AMS4165H | Aluminum Alloy, Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3511) Solution Heat Treated, Stress-Relieved by Stretching, and Straightened |
| SAE AMSA81596A | Aluminum Foil for Sandwich Construction |
| SAE AMS4122L | Aluminum Alloy Bars, Rods, and Wire Rolled or Cold Finished, and Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6, 7075-T651) Solution and Precipitation Heat Treated |
| SAE AMS4347D | Aluminum Alloy Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.5Mn (6013-T4) Solution Heat Treated and Naturally Aged |
| ASTM B 483/B483M : 2013 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| SAE AMS4354 | Aluminum Alloy, Plate, 7.9Zn – 1.8Cu - 2.0Mg - 0.10Zr (7099-T7451) Solution Heat Treated, Stress Relieved, and Overaged |
| ASTM B 247 : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings |
| ASTM B 236M : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric) (Withdrawn 2024) |
| SAE AMS4315A | Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T76 Sheet, -T7651 Plate) Solution and Precipitation Heat Treated |
| ASTM B 404/B404M : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Condenser and Heat-Exchanger Tubes with Integral Fins (Withdrawn 2006) |
| SAE AMS 4414 : 2013 | ALUMINUM ALLOY, HAND FORGINGS, 7.5ZN - 1.6CU - 1.5MG - 0.12ZR (7085-T7452), SOLUTION HEAT TREATED, COMPRESSION STRESS-RELIEVED, AND OVERAGED |
| SAE MAM4247B | Aluminum Alloy, Hand Forgings 7.7zn 2.4mg 1.6cu 0.16cr (7049-T7352) Solution Heat Treated, Stress Relieved By Compression, and Precipitation Heat Treated |
| SAE AMS4250B | Aluminum Alloy, Plate 8.1Zn - 2.3Mg - 1.0Cu - Zr (7449-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4159E | Aluminum Alloy, Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged |
| SAE AMS4232C | Aluminum Alloy Extrusions 2.7Cu - 2.2Li - 0.12Zr (2090-T86) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| SAE AMS4147D | Aluminum Alloy Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T7352) Solution Heat Treated, Stress Relieved by Compression, and Overaged |
| SAE AMS4460A | Aluminum Alloy, Clad Two Sides Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 24 Brazing Sheet) As Fabricated |
| SAE AMS4308B | Aluminum Alloy, Sheet 8.6Fe - 1.8Si - 1.3V (8009-H112) Powder Metallurgy Product, Strain Hardened |
| SAE AMS4163F | Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T3511) Solution Heat Treated, Stress-Relieved by Stretching, and Straightened |
| SAE AMS 4484 : 2013 | MAGNESIUM ALLOY CASTINGS, PERMANENT MOLD, 9.0AL - 2.0ZN (AZ92A-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS4336A | Aluminum Alloy, Extruded Rod, Bar, and Profiles (7055-T76511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4342F | Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T74511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged |
| SAE AMS4364 | Aluminum Alloy, Plate, 7.9Zn – 1.8Cu - 2.0Mg - 0.10Zr (7099-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4211B | Aluminum Alloy, Plate 6.2Zn - 1.9Cu - 2.1Mg - 0.10Zr (7040-T7451) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4351 | Aluminum Alloy, Plate (7065-T7651) 7.7Zn - 2.1Cu - 1.65Mg - 0.10Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4322A | Aluminum Alloy, Die Forgings 4.0Mg 1.3Li 1.2C 0.45 O₂ Mechanically Alloyed, As-Fabricated |
| SAE AMS4474A | Aluminum Alloy, Sheet and Plate 4.0Cu - 1.0Li - 0.40Mg - 0.35Ag - 0.13Zr (2195-T8) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4089E | Aluminum Alloy, Plate 1.6Cu - 2.2Mg - 0.22Cr - 5.7Zn (7475-T7651) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated |
| SAE AMS4633B | Bronze, Aluminum Silicon, Rods, Bars, and Forgings 90Cu - 7.0Al - 1.8Si Drawn and Stress Relieved (HR50) |
| SAE AMS4439G | Magnesium Alloy Castings 4.2Zn - 1.2 Rare Earths - 0.7Zr (ZE41A-T5) Precipitation Heat Treated |
| SAE AMS4214J | Castings, Aluminum Alloy Sand 5.0Si - 1.2Cu - 0.50Mg (355.0-T71) Solution Heat Treated and Overaged |
| SAE MAM4209B | Aluminum Alloy, Sheet, Alclad, 6.0cu 0.40zr, as Rolled |
| SAE AMS4068F | Aluminum Alloy, Drawn Seamless Tubing 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T3511) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4173F | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511 or T6510) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated |
| SAE AMS4071N | Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 2.5Mg – 0.25Cr (5052-O) Annealed |
| SAE AMS4299A | Aluminum Alloy, Plate (7449-T7951) 8.1Zn - 1.8Cu - 2.3Mg Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4302C | Aluminum Alloy, Laminated Sheet, Aramid Fiber Reinforced 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T761) 3, 5, 7, or 9 Ply |
| SAE AMS4413A | Aluminum Alloy, Plate 3.5Cu - 1.0Li - 0.40Mg - 0.35Mn - 0.45Ag - 0.12Zr (2050-T84) Solution Heat Treated, Stress Relieved, and Artificially Aged |
| SAE AMS4461 | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024-O, Sheet and Plate) Annealed; or when specified, “As Fabricated” (2024-F) |
| SAE AMS4210K | Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T51) Precipitation Heat Treated |
| SAE AMS4303C | Aluminum Alloy Plate 2.7Cu - 2.2Li - 0.12Zr (2090-T81) Solution Heat Treated, Cold Worked, and Aged |
| SAE AMS4118L | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 4.0Cu - 0.70Mn - 0.60Mg - 0.50Si (2017; -T4, -T451) Solution Heat Treated |
| SAE AMS4063E | Aluminum Alloy, Clad One Side, Sheet 1.25Mn - 0.12Cu (No. 11-0 Brazing Sheet) Annealed |
| SAE AMS4333D | Aluminum Alloy, Die Forgings 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged |
| SAE AMS QQ A 250 B : 2012 | ALUMINUM AND ALUMINUM ALLOY, PLATE AND SHEET GENERAL SPECIFICATION FOR |
| SAE AMS4025M | Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Annealed |
| SAE AMS 4152 : 2007 | ALUMINUM ALLOY EXTRUSIONS 4.4CU - 1.5MG - 0.60MN (2024-T3) SOLUTION HEAT TREATED |
| SAE AMS4236D | Aluminum Alloy Castings 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4427C | Magnesium Alloy Castings, Sand 4.0Y - 2.3Nd - 0.7Zr (WE43B - T6) Solution and Precipitation Heat Treated |
| SAE MAM4248B | Aluminum Alloy, Hand Forgings and Rolled Rings 1.0mg 0.60si 0.28cu 0.20cr Solution Heat Treated, Stress Relieved By Compression, and Precipitation Heat Treated |
| SAE AMS4221E | Aluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T8151) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4149E | Aluminum Alloy, Die and Hand Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T74) Solution and Precipitation Heat Treated |
| SAE AMS4375M | Sheet and Plate, Magnesium Alloy 3.0Al - 1.0Zn - 0.20Mn (AZ31B-O) Annealed and Recrystallized |
| SAE AMS4215H | Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (C355.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4452E | Magnesium Alloy, Investment Castings 8.7Al - 0.70Zn - 0.22Mn (AZ91C-T6) Solution and Precipitation Heat Treated |
| SAE AMS4284K | Aluminum Alloy Castings, Permanent Mold 7.0Si - 0.30Mg (356.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4442G | Magnesium Alloy Sand Castings 3.2 Rare Earths - 2.5Zn - 0.70Zr (EZ33A-T5) Precipitation Heat Treated |
| SAE AMSQQA225C | Aluminum and Aluminum Alloy, Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished; General Specification For |
| SAE AMS4120S | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 4.4Cu - 1.5Mg - 0.60Mn (2024) Solution Heat Treated and Naturally Aged (T4) Solution Heat Treated, Cold Worked, and Naturally Aged (T351) |
| SAE AMS4470A | Aluminum Alloy, Plate (7085-T7451) 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4313E | Aluminum Alloy, Rolled or Forged Rings 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T351, 2219-T352) Solution Heat Treated and Mechanically Stress Relieved |
| SAE AMS4453F | Magnesium Alloy, Investment Castings 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4041 : 2012-07 | ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 4.4CU - 1.5MG - 0.60MN (2024, -T3 SHEET/-T351 PLATE WITH 1-1/2% ALCLAD) SOLUTION HEAT TREATED, COLD WORKED AND NATURALLY AGED |
| SAE AMS4475B | Aluminum Alloy, Coiled Sheet, Alclad 4.4Cu – 1.5Mg – 0.60Mn (Alclad 2024; -T4 Coiled Sheet) Solution Heat Treated |
| SAE AMS4467B | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu 1.5Mg 0.60Mn (Alclad 2024, -T861 Sheet & Plate) Solution Heat Treated, 6% Cold Worked and Artificially Aged |
| SAE AMS4371B | Magnesium Alloy, Plate 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated |
| SAE AMS4366 | Aluminum Alloy, Extruded Profiles (2065-T84) 4.2Cu - 1.2Li – 0.52Mg – 0.32Mn – 0.32Ag - 0.1Zr Solution Heat Treated, Stress Relieved by Stretching and Artificially Aged |
| SAE AMS4485A | Magnesium Alloy, Extrusions 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated |
| SAE AMS4242C | Aluminum Alloy, Castings 4.7Cu - 0.60Ag - 0.35Mn - 0.25Mg - 0.25Ti (B201.0-T7) Solution Heat Treated and Overaged |
| MIL-STD-2073-1 Revision E:2008 | STANDARD PRACTICE FOR MILITARY PACKAGING |
| SAE AMS4434N | Magnesium Alloy Castings, Sand 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated |
| SAE AMS4117K | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire and Flash Welded Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6, -T651) |
| SAE AMS4125L | Aluminum Alloy Die Forgings, and Rolled or Forged Rings 0.9Si - 0.62Mg - 0.25Cr (6151-T6) Solution and Precipitation Heat Treated |
| SAE AMS4243B | Aluminum Alloy, Alclad Sheet 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (Alclad 7050-T76) Solution Heat Treated and Overaged |
| SAE AMS4161H | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4281G | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| ASTM B 211M : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) |
| SAE AMS4455G | Magnesium Alloy, Investment Castings 10Al (AM100A-T6) Solution and Precipitation Heat Treated |
| SAE AMS4402A | Aluminum Alloy, Extruded Profiles (2024-T432) 4.4Cu - 1.5Mg - 0.6Mn Annealed, Stretch Formed, Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4359 | Aluminum Alloy, Extruded Profiles (2395-T84) 3.95Cu - 1.15Li - 0.3Ag - 0.5Mg - 0.1Zr Solution Heat Treated, Stress Relieved by Stretching, and Aged |
| ASTM B 313M : 1988 | Specification for Aluminum and Aluminum-Alloy Round Welded Tubes (Metric) (Withdrawn 1990) |
| ASTM B 361 : 2016 : REDLINE | Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings |
| SAE AMS4037Q | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024; -T3 Flat Sheet, -T351 Plate) Solution Heat Treated |
| SAE MAM4141B | Aluminum Alloy, Die Forgings, 5.6zn 2.5mg 1.6cu 0.23cr Solution and Precipitation Heat Treated |
| SAE AMS4323C | Aluminum Alloy, Hand Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T7452) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4095D | Aluminum Alloy, Alclad Sheet and Plate 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T31; Sheet, Solution Heat Treated and Cold Worked Alclad 2219-T351; Plate, Solution Heat Treated and Stress Relieved |
| SAE AMS4040P | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024-O with 1 ½% Alclad); Annealed |
| SAE AMS4080P | Aluminum Alloy, Drawn Seamless Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Annealed |
| SAE AMS4088K | Aluminum Alloy, Drawn, Seamless Tubing 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated and Cold Worked |
| SAE AMS4338A | Aluminum Alloy, Extrusions 4.0Cu - 1.3Mg - 0.60Mn (2026-T3511) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS 4257 : 2014 | ALUMINUM ALLOY, EXTRUSION 3.7CU - 1.15LI - 0.5ZN - 0.45AG - 0.4MG - 0.3MN - 0.1ZR (2055-T84) SOLUTION HEAT TREATED, STRESS RELIEVED BY STRETCHING 2% TO 5% AND AGED |
| ASTM B 316/B316M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
| SAE AMS 4372 : 2018 | ALUMINUM ALLOY, PLATE, 3.5CU - 1.0LI - 0.40MG - 0.35MN - 0.45AG - 0.12ZR (2050-T34), SOLUTION HEAT TREATED AND STRESS RELIEVED |
| SAE AMS4355 | Aluminum Alloy, Discontinuously Reinforced Hot Isostatically Pressed Shapes 2124A/SiC/25p (3μm) (T1P) |
| SAE AMS5636F | Steel, Corrosion-Resistant, Bars and Wire 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn 100 ksi (689 MPa) Tensile Strength |
| SAE AMS4124E | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73, T7351) Solution Heat Treated, Stress Relieved by Stretching, and Overaged |
| SAE AMS4132G | Aluminum Alloy, Die and Hand Forgings, Rolled Rings, and Forging Stock 2.3Cu - 1.6Mg - 1.1Fe - 1.0Ni - 0.18Si - 0.07Ti (2618-T61) Solution and Precipitation Heat Treated |
| ASTM B 881 : 2017 : REDLINE | Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products |
| ASTM B 90/B90M : 2015 : REDLINE | Standard Specification for Magnesium-Alloy Sheet and Plate |
| ASTM B 236 : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| SAE AMS4387F | Magnesium Alloy Extrusions 2.3Zn - 0.62Zr (ZK21A-F) As Extruded |
| SAE AMS 4426 : 2013 | CASTINGS, SAND, MAGNESIUM ALLOY 5.1Y - 3.0RE - 0.70ZR (WE54-T6) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS4195D | Aluminum Alloy Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024 and 1-1/2% Alclad 2024-T861 Flat Sheet; 1-1/2% Alclad 2024-T861 Plate) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| SAE AMS4255B | Aluminum Allloy, Clad One Side Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 21 Brazing Sheet) As Fabricated |
| SAE AMS4457 | Aluminum Alloy, Sheet 3.5Cu - 1.1Li - 0.50Mg - 0.40Ag - 0.12Zr (2098-T8) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4082P | Aluminum Alloy, Seamless Drawn Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMSA22771D | Aluminum Alloy Forgings, Heat Treated |
| SAE AMS4002A | Aluminum Alloy Tubing, Seamless, Drawn 1.8Cu - 1.0Mg - 0.8Si - 0.20Cr Solution Heat Treated, Stress-Relieved by Stretching, and Aged (2013-T6511) |
| SAE AMS4480 | Aluminum Alloy, Seamless Drawn Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| SAE AMS4031J | Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-O) Annealed or when specified, “As Fabricated” (2219-F) |
| SAE AMS4086N | Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated, Cold Worked, and Naturally Aged |
| SAE AMS4345B | Aluminum Alloy, Extrusions 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T77511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged |
| SAE AMST81915B | Titanium and Titanium-Alloy Castings, Investment |
| SAE AMS4085D | Aluminum Alloy Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T761) Solution Heat Treated and Overaged |
| SAE AMS4444E | Magnesium Alloy Castings, Sand 6.0Zn - 0.80Zr (ZK61A-T5) Precipitation Heat Treated |
| SAE AMS4407A | Aluminum Alloy, Plate (7056-T7651) 9.1Zn - 1.6Cu - 1.9Mg Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4478A | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T81 Sheet, -T851 Plate) Solution Heat Treated, Cold Worked and Artificially Aged |
| ASTM B 234 : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
| SAE AMS4356 | Aluminum Alloy Seamless Drawn Round Tubing 2.3 Cu – 8.0 Zn – 2.0 Mg - 0.16 Zr (7155-T76) Solution Heat Treated and Aged |
| SAE AMS4205D | Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T7451) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4326A | Aluminum Alloy, 2013, Extruded Bar, Rod, and Profiles 1.0Mg - 0.80Si - 1.8Cu - 0.20Cr (2013 -T6511) Solution Heat Treated, Stress-Relieved by Stretching, and Aged |
| SAE AMS 4305 : 2012 | ALUMINUM ALLOY, EXTRUDED PROFILES (7449-T79511) 8.1ZN - 1.8CU - 2.2MG - 0.16ZR SOLUTION HEAT TREATED, STRESS RELIEVED, AND OVERAGED (COMPOSITION SIMILAR TO UNS A97449) |
| SAE AMS4425D | Magnesium Alloy Castings, Sand 5.8Zn - 2.5RE - 0.70Zr (ZE63-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4279 : 2011 | ALUMINUM ALLOY, ALCLAD SHEET, 4.4CU - 1.5MG - 0.60MN (2024 -T4 FLAT SHEET), SOLUTION HEAT TREATED, HIGH FORMABILITY |
| SAE AMS4404A | Aluminum Alloy, Extruded Profiles (6056-T4511) 1.0Si - 0.90Mg - 0.80Cu - 0.60Mn - 0.40Zn Solution Heat Treated and Stress-Relieved by Stretching |
| SAE AMS4174E | Aluminum Alloy, Flash Welded Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73) Solution and Precipitation Heat Treated |
| SAE AMS4087H | Aluminum Alloy Tubing, Seamless, Drawn (2024-0) Reinstate Composition Annealed |
| SAE AMS4123H | Aluminum Alloy, Rolled or Cold Finished Bars and Rods (7075-T651) Solution and Precipitation Heat Treated |
| SAE AMS4309B | Aluminum Alloy Extrusions 8.6Fe - 1.8Se - 1.3V (8009-H112) Powder Metallurgy Product, Strain-Hardened |
| SAE AMS4156K | Aluminum Alloy, Extrusions 0.68Mg - 0.40Si (6063-T6) Solution and Precipitation Heat Treated |
| SAE AMS4056H | Aluminum Alloy, Sheet and Plate 4.4Mg - 0.70Mn - 0.15Cr (5083-O) Annealed |
| SAE AMS4150M | Aluminum Alloy, Extrusions and Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS4201F | Aluminum Alloy Plate 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4337B | Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4340E | Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged |
| SAE AMS4437F | Magnesium Alloy Castings, Sand 8.7Al - 0.70Zn (AZ91C-T6) Solution Heat Treated and Aged |
| ASTM B 308M : 1988 | Specification for Aluminum-Alloy 6061-T6 Standard Structural Shapes, Rolled or Extruded (Metric) (Withdrawn 1990) |
| PPP-C-96 Revision E:1992 | CAN, METAL, 28 GAGE AND LIGHTER |
| ASTM D 3950 : 2017 : REDLINE | Standard Specification for Strapping, Nonmetallic (and Joining Methods) |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM D 3953 : 2015 : REDLINE | Standard Specification for Strapping, Flat Steel and Seals |
| A-A-1249 Revision A:1993 | PAPER, WRAPPING, TISSUE |
| PPP-B-566 Revision E:1974 | BOX, FOLDING, PAPERBOARD |
| AHA A135.4 : 2012 | BASIC HARDBOARD |
| PPP-D-705 Revision E:1994 | DRUM, SHIPPING AND STORAGE, STEEL, 16 AND 30 GALLON CAPACITY |
| PPP-T-495 Revision B:1974 | TUBES, MAILING, AND FILING |
| MIL-PRF-121 Revision G:2001 | BARRIER MATERIALS, GREASEPROOF, WATERPROOF, FLEXIBLE, HEAT-SEALABLE |
| ASTM D 1732 : 2003 | Standard Practices for Preparation of Magnesium Alloy Surfaces for Painting |
| MIL-STD-3010 Revision B:2008 | Test Procedures for Packaging Materials and Containers |
| A-A-55057 Revision B:2010 | PANELS, WOOD/WOOD BASED: CONSTRUCTION AND DECORATIVE |
| ASTM D 1974 : 1998 | Standard Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes |
| MIL-DTL-17667 Revision E:2005 | PAPER, WRAPPING, CHEMICALLY NEUTRAL (NON-CORROSIVE) |
| ASTM D 779 : 2016 | Standard Test Method for Determining the Water Vapor Resistance of Sheet Materials in Contact with Liquid Water by the Dry Indicator Method |
| ASTM D 4727/D4727M : 2017 : REDLINE | Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes |
| MIL-PRF-7870 Revision E:2015 | LUBRICATING OIL: GENERAL PURPOSE, LOW-TEMPERATURE (NATO O-142) |
| PPP-D-729 Revision E:1977 | DRUMS, SHIPPING AND STORAGE, STEEL, 55 GALLON (208 LITERS) |
| MIL-PRF-32033 Revision A:2016 | LUBRICATING OIL, GENERAL PURPOSE, PRESERVATIVE (WATER-DISPLACING, LOW TEMPERATURE) |
| PPP-P-704 Revision E:1981 | Pails, Metal: (Shipping, Steel, 1 through 12 Gallons) |
| MIL-PRF-16173 Revision E:1993 | CORROSION PREVENTATIVE COMPOUND, SOLVENT CUTBACK, COLD-APPLICATION |
| MIL-C-11796 Revision C:1986 | CORROSION PREVENTIVE COMPOUND, PETROLATUM, HOT APPLICATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.