ASTM B 666/B666M : 2015 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Identification Marking of Aluminum and Magnesium Products
Available format(s)
PDF
Superseded date
08-05-2020
Superseded by
Language(s)
English
Published date
01-10-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 02.02, 2015 Describes the physical item marking requirements for identification purposes for aluminum and magnesium products.
| Committee |
B 07
|
| DevelopmentNote |
Supersedes ASTM B 666M. (12/2001) Supersedes SAE AMS STD 184. (09/2006) Supersedes FED STD 184 (B). (11/2006)
|
| DocumentType |
Redline
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice establishes the physical item marking requirements for identification purposes for aluminum and magnesium products. Package marking for shipment and inspection acceptance is not within the scope of this standard.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| SAE AMS4028H | Aluminum Alloy Sheet and Plate 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-O) Annealed |
| ASTM B 91 : 2017 : REDLINE | Standard Specification for Magnesium-Alloy Forgings |
| SAE AMS4069F | Aluminum Alloy, Drawn, Round Seamless Tubing Close Tolerance 2.5Mg - 0.25Cr (5052-O) Annealed |
| ASTM B 403 : 2012 : REDLINE | Standard Specification for Magnesium-Alloy Investment Castings |
| SAE AMS4272 | Aluminum Alloy, Alclad Sheet and Plate (Alclad 2029-T8) 3.6 Cu, 0.30 Mn, 0.95 Mg, 0.40 Ag, 0.12 Zr Solution Heat Treated, Cold Worked and Aged |
| ASTM B 317/B317M : 2007 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| SAE AMS4466A | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T361 Sheet & Plate) Solution Heat Treated, 6% Cold Worked and Naturally Aged |
| SAE AMS4332 | Aluminum Alloy, Extruded Profiles (7349-T76511) 8.1Zn - 1.7Cu - 2.2Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4405A | Aluminum Alloy, Alclad Sheet (6156-T4) 1.0Si - 0.90Cu - 0.60Mn - 0.90Mg Solution Heat Treated and Naturally Aged |
| SAE AMS4295D | Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr (2219 - O, F, T31, T351, T37, T81, T851, T87) |
| SAE AMS4306C | Aluminum Alloy, Plate 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T6151) Solution Heat Treated, Stress Relieved, and Aged |
| SAE AMS4083L | Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4401 : 2011 | ALUMINUM ALLOY PLATE (7140-T7451), 6.6ZN - 1.8CU - 2.0MG - 0.10ZR, SOLUTION HEAT TREATED, STRESS RELIEVED AND OVERAGED (COMPOSITION SIMILAR TO UNS A97140) |
| SAE AMS4044N | Aluminum Alloy, Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr Annealed (7075-O) or when specified, “As Fabricated” (7075-F) |
| ASTM B 211 : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| SAE AMS4465A | Aluminum Alloy, Clad One Side Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 23 Brazing Sheet) As Fabricated |
| SAE AMS4046G | Aluminum Alloy Sheet and Plate, Alclad One Side 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad One Side 7075; -T6 Sheet -T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4477A | Aluminum Alloy, Coiled Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-T4) Solution Treated |
| SAE AMS4312D | Aluminum Alloy, Rolled or Forged Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T651, 6061-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated |
| SAE AMS 4203 : 2012 | ALUMINUM ALLOY, PLATE, 6.2ZN - 1.8CU - 2.4MG - 0.13ZR (7010-T7351) SOLUTION HEAT TREATED, STRESS RELIEVED AND PRECIPITATION HEAT TREATED (COMPOSITION SIMILAR TO UNS A97010) |
| SAE AMS4409 | Aluminum Alloy, Plate 4.0Zn - 2.0Mg - 0.32Mn (7019-T651) Solution Heat Treated, Stress Relieved and Artificially Aged |
| SAE AMS4064F | Aluminum Alloy, Clad Two Sides Sheet 1.25Mn - 0.12Cu (No. 12-0 Brazing Sheet) Annealed |
| SAE AMS4299A | Aluminum Alloy, Plate (7449-T7951) 8.1Zn - 1.8Cu - 2.3Mg Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4311E | Aluminum Alloy, Rolled or Forged Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T7351, 7075-T7352) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated |
| QQ-A-225 Revision G:1990 | ALUMINUM AND ALUMINUM ALLOY BAR, ROD, WIRE, OR SPECIAL SHAPES, ROLLED, DRAWN, OR COLD FINISHED, GENERAL SPECIFICATION FOR |
| MIL A 46192 : B | ALUMINUM ALLOY ARMOR ROLLED PLATE (1/2 TO 4 INCHES THICK), WELDABLE (ALLOY 2519) |
| SAE AMS4324A | Aluminum Alloy, Extruded Rod, Bar and Profiles (7055-T74511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4330C | Aluminum Alloy, Plate (2297-T87) 2.8Cu - 1.5Li - 0.30Mn - 0.12Zr Solution Heat Treated, Stretched, and Artificially Aged |
| SAE AMS4416B | Aluminum Alloy, Extruded Profiles (2196-T8511) 2.9Cu - 1.7Li - 0.4Mg - 0.4Ag - 0.10Zr Solution Heat Treated, Stress Relieved by Stretching and Artificially Aged |
| SAE AMS4077H | Aluminum Alloy Sheet and Plate, Alclad One Side 4.4Cu - 1.5Mg - 0.60Mn (Clad One Side 2024-O) Annealed |
| SAE AMS4276B | Aluminum Alloy, Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-O) Annealed, Fine Grained |
| SAE AMS 4473 : 2017 | ALUMINUM ALLOY PLATE (2624-T39), 4.1CU - 1.4MG - 0.6MN, SOLUTION HEAT TREATED, COLD WORKED AND NATURALLY AGED |
| SAE AMS4462A | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T3 Sheet, -T351 Plate) Solution Heat Treated, Cold Worked and Naturally Aged |
| SAE AMS4015M | Aluminum Alloy, Sheet and Plate 2.5Mg - 0.25Cr (5052-O) Annealed |
| SAE AMS4162E | Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T8511) Solution Treated, Stress Relief Stretched, Straightened, and Precipitation Heat Treated |
| SAE AMS4365 | Aluminum Alloy, Plate, 7.9Zn – 1.2Cu - 2.1Mg - 0.10Zr (7097-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4345B | Aluminum Alloy, Extrusions 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T77511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged |
| SAE AMS4304B | Aluminum Alloy, Discontinuously Reinforced Sheet 2009/SiC/15w (T8P) Solution Heat Treated, Stretched, and Precipitation Heat Treated |
| SAE AMS4374 | Aluminum Alloy, Extruded Profiles 8.9Zn - 2.2Cu - 2.2Mg - 0.15Zr (7136-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged |
| SAE AMSWWT700B | Tube, Aluminum and Aluminum Alloy, Drawn, Seamless, General Specification for |
| SAE AMS4344D | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged |
| ASTM B 928/B928M : 2015 : REDLINE | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| SAE AMS4353 | Aluminum Alloy, Extruded Round Rod 3.5Cu - 1.0Li - 0.40Mg - 0.45Ag - 0.12Zr (2050-T84) Solution Heat Treated, Stress Relieved by Stretching, and Artificially Aged |
| SAE AMS4601A | Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr Solution Heat Treated, Cold Worked and Naturally Aged (2219 -T31/-T351) |
| SAE AMS4350N | Magnesium Alloy, Extrusions 6.5A1 - 0.95Zn (AZ61A-F) As Extruded |
| SAE AMS4213A | Aluminum Alloy Plate (2027-T351) 4.4Cu - 1.2Mg - 0.8Mn - 0.10Zr Solution Heat Treated, Cold Worked and Naturally Aged |
| SAE AMS4268A | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn; (2024-T81 Sheet, -T851 Plate) Solution Heat Treated, Cold Worked and Artificially Aged |
| SAE AMS4415A | Aluminum Alloy Extrusions 8.9Zn - 2.2Cu - 2.2Mg - 0.15Zr (7136-T76511, -T76510) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged |
| SAE AMS4459A | Aluminum Alloy, Extrusion 2.7Cu - 1.8Li - 0.7Zn - 0.3Mn - 0.3Mg - 0.08Zr (2099-T81) Solution Heat Treated, Stress Relieved by Stretching 1 to 3% and Aged |
| SAE AMS4096D | Aluminum Alloy Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (Alclad 2219-O) Annealed |
| SAE AMS4287A | Aluminum Alloy, Extrusion 2.7Cu - 1.8Li - 0.7Zn - 0.3Mn - 0.3Mg - 0.08Zr (2099-T83) Solution Heat Treated, Stress Relieved by Stretching 1% to 4% and Aged |
| ASTM B 317/B317M : 2007 : R2015 : EDT 1 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 491/B491M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications |
| ASTM B 317/B317M : 2007 : R2015 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 316/B316M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
| SAE AMS4468 | Aluminum Alloy, Plate 5.0Cu - 0.4Mn - 0.5Mg - 0.4Ag (2139-T84) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4035M | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024-O) Annealed; or when specified, “As Fabricated” (2024-F) |
| SAE AMS4113F | Aluminum Alloy, Extruded Profiles 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4472 : 2017 | ALUMINUM ALLOY, PLATE, 4.0CU - 1.0LI - 0.40MG - 0.35AG - 0.13ZR (2195-T34), SOLUTION HEAT TREATED AND STRESS RELIEVED |
| SAE AMS4315A | Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T76 Sheet, -T7651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4066C | Aluminum Alloy, Drawn, Round Seamless Tubing 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti - (2219-T8511) Solution Heat Treated, Stress Relieved by Stretching and Precipitation Heat Treated |
| SAE AMS4116J | Aluminum Alloy, Bars, Rods, and Wire 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T4) Cold Finished, Solution Heat Treated and Naturally Aged |
| ASTM B 236 : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| SAE AMS4172F | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4511 or T4510) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4194E | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024 -T361 Sheet/Plate with 1½% Alclad) Solution Heat Treated, 6% Cold Worked and Naturally Aged |
| AASHTO M 197 : 2006 | SPECIFICATION FOR ALUMINUM ALLOY SHEET FOR CORRUGATED ALUMINUM PIPE |
| SAE AMS4256C | Aluminum Alloy, Clad Two Sides Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 22 Brazing Sheet) As Fabricated |
| SAE AMS4269A | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn; (2024-T361), Solution Heat Treated and Cold Worked |
| SAE AMS4341E | Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged |
| SAE AMS4100F | Aluminum Alloy, Alclad, Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (Alclad 7475-T761) Solution and Precipitation Heat Treated |
| SAE AMS4335A | Forgings, Aluminum Alloys 2xxx and 7xxx, Heat-Treated, Finished-Part Properties: Short-Transverse Tensile Properties and Fracture Toughness |
| SAE AMS4081J | Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4296C | Aluminum Alloy, Alclad Sheet and Plate 4.3Cu - 1.4Mg - 0.60Mn (Alclad 2524-T3) Solution Heat Treated and Cold Worked |
| SAE AMS4476 | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-O) Annealed |
| SAE AMS4361 | Aluminum Alloy, Plate (7065-T7451) 7.7Zn - 2.1Cu - 1.65Mg - 0.10Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4128D | Aluminum Alloy Bars, Rolled or Cold Finished 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4469 | Aluminum Alloy Tubing, Seamless, Drawn 1.8 Cu - 1.0 Mg - 0.8 Si - 0.20 Cr Solution Heat Treated, Stress-Relieved by Stretching, and Aged (2013-T4511) |
| SAE AMS4617A | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73, 7075-T73511, 7075-T73510) Solution Heat Treated, Stress Relieved by Stretching when required, and Overaged |
| SAE AMS4208C | Aluminum Alloy Sheet 6.0Cu - 0.40Zr - (2004-F) As Rolled |
| SAE AMS4121J | Aluminum Alloy Bars, Rods, and Wire, Rolled, Drawn, or Cold Finished 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6, -T651) Solution and Precipitation Heat Treated |
| SAE AMS4048P | Aluminum Alloy Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075-O) Annealed or when specified, “As Fabricated” (Alclad 7075-F) |
| SAE AMS4050J | Aluminum Alloy, Plate 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7451) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4202D | Aluminum Alloy Plate 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T7351) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated |
| SAE AMS4298A | Aluminum Alloy, Alclad Sheet 3.8Cu – 1.0Mg – 0.30Mn – 0.60Zn (Alclad 2056-T3) Solution Heat Treated and Cold Worked |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| SAE AMS4216B | Aluminum Alloy, Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.50Mn (6013-T6) Solution Heat Treated and Artificially Aged |
| SAE AMS4464A | Aluminum Alloy Plate (2624-T351) 4.1Cu - 1.4Mg - 0.6Mn Solution Heat Treated, Cold Worked and Naturally Aged |
| SAE AMS4329B | Aluminum Alloy, Plate (7085-T7651) 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4036L | Aluminum Alloy Sheet and Plate, Alclad One Side 4.4Cu - 1.5Mg - 0.60Mn Alclad One Side 2024 and 1-1/2% Alclad One Side 2024-T3 Sheet; 1-1/2% Alclad One Side 2024-T351 Plate |
| SAE AMS4204C | Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T7651) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| ASTM B 107/B107M : 2013 : REDLINE | Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| SAE AMS 4257 : 2014 | ALUMINUM ALLOY, EXTRUSION 3.7CU - 1.15LI - 0.5ZN - 0.45AG - 0.4MG - 0.3MN - 0.1ZR (2055-T84) SOLUTION HEAT TREATED, STRESS RELIEVED BY STRETCHING 2% TO 5% AND AGED |
| ASTM B 211M : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) (Withdrawn 2019) |
| ASTM B 209M : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) |
| ASTM B 236 : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 211 : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| ASTM B 236M : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) [Metric] |
| SAE AMS4319B | Aluminum Alloy, Rolled or Cold Finished, Bars and Rods 12.2Si - 1.0Mg - 0.90Cu - 0.90Ni (4032-T651) Solution Heat Treated, Stress-Relieved, and Artificially Aged |
| SAE AMS4410 | Aluminum Alloy Plate (7081-T7451) 7.2Zn - 1.5Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged |
| ASTM B 483/B483M : 2013 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications |
| SAE AMS4115J | Aluminum Alloy, Rolled or Cold-Finished, Bars, Rods, Wire, and Flash Welded Rings Annealed 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) |
| SAE AMS4314D | Aluminum Alloy Rings, Rolled or Forged 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T651, 2014-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4078J | Aluminum Alloy Sheet and Plate 5.6Zn – 2.5Mg-1.6Cu-0.23Cr 7075: (-T73 Sheet, -T7351 Plate) Solution Heat Treated and Overaged |
| SAE AMS4458A | Aluminum Alloy, Plate (2.7 Cu - 1.8 Li - 0.7 Zn) 2099-T86 Solution Heat Treated, Cold Worked and Artificially Aged |
| ASTM B 234M : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
| SAE AMS2772G | Heat Treatment of Aluminum Alloy Raw Materials |
| SAE AMS4278B | Aluminum Alloy, Alclad Sheet 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075-0) Annealed, Fine Grained |
| SAE AMS4325 | Aluminum Alloy, Extruded Wide Panel Profiles (7150-T77511) 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr Solution Heat Treated, Stress-Relieved, Straightened and Overaged |
| SAE AMS4200C | Aluminum Alloy Plate 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T7351) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4277B | Aluminum Alloy, Sheet 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-O) Annealed, Fine Grained |
| SAE AMS4412A | Aluminum Alloy, Sheet 3.2Cu - 0.52Mg - 0.30Ag - 0.12Zr (2198-T8) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4339B | Aluminum Alloy, Rolled or Cold Finished Bars and Rods 4.4Cu - 1.5Mg - 0.60Mn (2024-T851) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4343D | Aluminum Alloy, Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7149-T73511) Solution Heat Treated, Stress Relieved by Stretching, and Overaged |
| SAE AMS4154R | Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6, 7075-T6510, 7075-T6511) Solution Heat Treated, Stress Relieved by Stretching when Required and Precipitation Heat Treated |
| SAE AMS4252B | Aluminum Alloy, Plate 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T7751) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4079H | Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Close Tolerance, Annealed |
| SAE AMS4186D | Aluminum Alloy Bars, Rods, and Wire, Rolled or Cold Finished 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-F) As Fabricated, or when specified, Annealed (7075-O) |
| SAE AMS4193D | Aluminum Alloy Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024-T861) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| SAE AMS4002A | Aluminum Alloy Tubing, Seamless, Drawn 1.8Cu - 1.0Mg - 0.8Si - 0.20Cr Solution Heat Treated, Stress-Relieved by Stretching, and Aged (2013-T6511) |
| SAE AMS4293 | Aluminum Alloy Extrusions 7.9Zn - 1.6Cu - 2.2Mg - 0.16Cr (7249-T76511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged |
| SAE AMS4183A | Aluminum Alloy, Extruded Profiles (2027-T3511) 4.4Cu - 1.2Mg - 0.8Mn - 0.10Zr Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4090F | Aluminum Alloy, Plate 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T651) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4094D | Aluminum Alloy, Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T81 Sheet Solution Heat Treated, Cold Worked, and Precipitation Heat Treated Alclad 2219-T851 Plate Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4209C | Aluminum Alloy Sheet, Alclad 6.0Cu - 0.40Zr - (2004-F) As Rolled |
| SAE AMS4368 | Aluminum Alloy, Discontinuously Reinforced Hot Isostatically Pressed Shapes 6061B/SiC/40p (3μm) (T1P) |
| SAE AMS4331 | Aluminum Alloy Extrusions 7.8Zn - 2.6Mg - 2.0Cu - 0.10Zr - (7068-T6511) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4070N | Aluminum Alloy, Drawn, Round Seamless Tubing 2.5Mg - 0.25Cr (5052-O) Annealed |
| SAE AMS4027N | Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4160H | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Annealed |
| SAE AMS4411 | Aluminum Alloy Plate (7081-T7651) 7.2Zn - 1.5Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged |
| SAE AMS4045L | Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4479 | Aluminum Alloy, Extruded Profiles (2824-T3511) 4.0Cu - 1.35Mg - 0.7Mn Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4463A | Aluminum Alloy, Plate (7255-T7751) 8.0Zn - 2.3Cu - 2.0Mg - 0.12Zr Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4084E | Aluminum Alloy Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T61) Solution and Precipitation Heat Treated |
| SAE AMS4026M | Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T4 Sheet, -T451 Plate) Solution Heat Treated and Naturally Aged |
| SAE AMS4101F | Aluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T851) Solution Heat Treated, Stretched, and Precipitation Heat Treated |
| SAE AMS4017L | Aluminum Alloy Sheet and Plate 2.5Mg - 0.25Cr (5052-H34) Strain-Hardened, Half-Hard, and Stabilized |
| SAE AMS4371B | Magnesium Alloy, Plate 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated |
| SAE AMS4157E | Aluminum Alloy Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T73511) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4327A | Aluminum Alloy, Plate (2098-O) 3.5Cu - 1.1Li - 0.50Mg - 0.40Ag - 0.11Zr Annealed |
| SAE AMS4165H | Aluminum Alloy, Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3511) Solution Heat Treated, Stress-Relieved by Stretching, and Straightened |
| SAE AMSA81596A | Aluminum Foil for Sandwich Construction |
| SAE AMS4122L | Aluminum Alloy Bars, Rods, and Wire Rolled or Cold Finished, and Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6, 7075-T651) Solution and Precipitation Heat Treated |
| SAE AMS4255B | Aluminum Allloy, Clad One Side Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 21 Brazing Sheet) As Fabricated |
| SAE AMS4205D | Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T7451) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4347D | Aluminum Alloy Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.5Mn (6013-T4) Solution Heat Treated and Naturally Aged |
| ASTM B 483/B483M : 2013 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| ASTM B 744/B744M : 2015 : REDLINE | Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe |
| SAE AMS4354 | Aluminum Alloy, Plate, 7.9Zn – 1.8Cu - 2.0Mg - 0.10Zr (7099-T7451) Solution Heat Treated, Stress Relieved, and Overaged |
| ASTM B 236M : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric) (Withdrawn 2024) |
| SAE AMS4159E | Aluminum Alloy, Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged |
| SAE AMS4599A | Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr Solution and Precipitation Heat Treated (2219 -T81/-T851) |
| SAE AMS4232C | Aluminum Alloy Extrusions 2.7Cu - 2.2Li - 0.12Zr (2090-T86) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| SAE AMS4460A | Aluminum Alloy, Clad Two Sides Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 24 Brazing Sheet) As Fabricated |
| SAE AMS4163F | Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T3511) Solution Heat Treated, Stress-Relieved by Stretching, and Straightened |
| SAE AMS4336A | Aluminum Alloy, Extruded Rod, Bar, and Profiles (7055-T76511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4274A | Aluminum Alloy, Alclad Sheet 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024-0) Annealed, Fine Grain |
| SAE AMS4342F | Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T74511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged |
| SAE AMS4364 | Aluminum Alloy, Plate, 7.9Zn – 1.8Cu - 2.0Mg - 0.10Zr (7099-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4211B | Aluminum Alloy, Plate 6.2Zn - 1.9Cu - 2.1Mg - 0.10Zr (7040-T7451) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4351 | Aluminum Alloy, Plate (7065-T7651) 7.7Zn - 2.1Cu - 1.65Mg - 0.10Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| SAE AMS4474A | Aluminum Alloy, Sheet and Plate 4.0Cu - 1.0Li - 0.40Mg - 0.35Ag - 0.13Zr (2195-T8) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4089E | Aluminum Alloy, Plate 1.6Cu - 2.2Mg - 0.22Cr - 5.7Zn (7475-T7651) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated |
| SAE AMS4068F | Aluminum Alloy, Drawn Seamless Tubing 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T3511) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4173F | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511 or T6510) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated |
| SAE AMS4071N | Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 2.5Mg – 0.25Cr (5052-O) Annealed |
| SAE AMS4413A | Aluminum Alloy, Plate 3.5Cu - 1.0Li - 0.40Mg - 0.35Mn - 0.45Ag - 0.12Zr (2050-T84) Solution Heat Treated, Stress Relieved, and Artificially Aged |
| SAE AMS4461 | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024-O, Sheet and Plate) Annealed; or when specified, “As Fabricated” (2024-F) |
| SAE AMS4118L | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 4.0Cu - 0.70Mn - 0.60Mg - 0.50Si (2017; -T4, -T451) Solution Heat Treated |
| SAE AMS4303C | Aluminum Alloy Plate 2.7Cu - 2.2Li - 0.12Zr (2090-T81) Solution Heat Treated, Cold Worked, and Aged |
| ASTM B 234 : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
| SAE AMS4404A | Aluminum Alloy, Extruded Profiles (6056-T4511) 1.0Si - 0.90Mg - 0.80Cu - 0.60Mn - 0.40Zn Solution Heat Treated and Stress-Relieved by Stretching |
| SAE AMS4063E | Aluminum Alloy, Clad One Side, Sheet 1.25Mn - 0.12Cu (No. 11-0 Brazing Sheet) Annealed |
| SAE AMS4025M | Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Annealed |
| SAE AMS 4152 : 2007 | ALUMINUM ALLOY EXTRUSIONS 4.4CU - 1.5MG - 0.60MN (2024-T3) SOLUTION HEAT TREATED |
| SAE AMS4221E | Aluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T8151) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
| SAE AMS4375M | Sheet and Plate, Magnesium Alloy 3.0Al - 1.0Zn - 0.20Mn (AZ31B-O) Annealed and Recrystallized |
| SAE AMSQQA225C | Aluminum and Aluminum Alloy, Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished; General Specification For |
| SAE AMS4120S | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 4.4Cu - 1.5Mg - 0.60Mn (2024) Solution Heat Treated and Naturally Aged (T4) Solution Heat Treated, Cold Worked, and Naturally Aged (T351) |
| SAE AMS4470A | Aluminum Alloy, Plate (7085-T7451) 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr Solution Heat Treated, Stress-Relieved, and Overaged |
| AASHTO M 219 : 1992 | SPECIFICATION FOR CORRUGATED ALUMINUM ALLOY STRUCTURAL PLATE FOR FIELD-BOLTED PIPE, PIPE-ARCHES, AND ARCHES |
| SAE AMS 4041 : 2012-07 | ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 4.4CU - 1.5MG - 0.60MN (2024, -T3 SHEET/-T351 PLATE WITH 1-1/2% ALCLAD) SOLUTION HEAT TREATED, COLD WORKED AND NATURALLY AGED |
| SAE AMS4475B | Aluminum Alloy, Coiled Sheet, Alclad 4.4Cu – 1.5Mg – 0.60Mn (Alclad 2024; -T4 Coiled Sheet) Solution Heat Treated |
| SAE AMS4467B | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu 1.5Mg 0.60Mn (Alclad 2024, -T861 Sheet & Plate) Solution Heat Treated, 6% Cold Worked and Artificially Aged |
| SAE AMS4366 | Aluminum Alloy, Extruded Profiles (2065-T84) 4.2Cu - 1.2Li – 0.52Mg – 0.32Mn – 0.32Ag - 0.1Zr Solution Heat Treated, Stress Relieved by Stretching and Artificially Aged |
| SAE AMS4485A | Magnesium Alloy, Extrusions 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated |
| SAE AMS4117K | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire and Flash Welded Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6, -T651) |
| SAE AMS4161H | Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4243B | Aluminum Alloy, Alclad Sheet 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (Alclad 7050-T76) Solution Heat Treated and Overaged |
| ASTM B 211M : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) |
| SAE AMS4359 | Aluminum Alloy, Extruded Profiles (2395-T84) 3.95Cu - 1.15Li - 0.3Ag - 0.5Mg - 0.1Zr Solution Heat Treated, Stress Relieved by Stretching, and Aged |
| SAE AMS4037Q | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024; -T3 Flat Sheet, -T351 Plate) Solution Heat Treated |
| SAE AMS4206C | Aluminum Alloy, Plate (7055-T7751) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4095D | Aluminum Alloy, Alclad Sheet and Plate 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T31; Sheet, Solution Heat Treated and Cold Worked Alclad 2219-T351; Plate, Solution Heat Treated and Stress Relieved |
| SAE AMS4080P | Aluminum Alloy, Drawn Seamless Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Annealed |
| SAE AMS4088K | Aluminum Alloy, Drawn, Seamless Tubing 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated and Cold Worked |
| SAE AMS4040P | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024-O with 1 ½% Alclad); Annealed |
| SAE AMS4164H | Aluminum Alloy, Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3510) Stress-Relief Stretched, Unstraightened |
| SAE AMS4338A | Aluminum Alloy, Extrusions 4.0Cu - 1.3Mg - 0.60Mn (2026-T3511) Solution Heat Treated and Stress Relieved by Stretching |
| SAE AMS4250B | Aluminum Alloy, Plate 8.1Zn - 2.3Mg - 1.0Cu - Zr (7449-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| AASHTO M 196 : 1992 | SPECIFICATION FOR CORRUGATED ALUMINUM PIPE FOR SEWERS AND DRAINS |
| SAE AMS 4372 : 2018 | ALUMINUM ALLOY, PLATE, 3.5CU - 1.0LI - 0.40MG - 0.35MN - 0.45AG - 0.12ZR (2050-T34), SOLUTION HEAT TREATED AND STRESS RELIEVED |
| SAE AMS4355 | Aluminum Alloy, Discontinuously Reinforced Hot Isostatically Pressed Shapes 2124A/SiC/25p (3μm) (T1P) |
| SAE AMS4352J | Magnesium Alloy, Extrusions 5.5Zn - 0.45Zr (ZK60A-T5) Precipitation Heat Treated |
| SAE AMS4124E | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73, T7351) Solution Heat Treated, Stress Relieved by Stretching, and Overaged |
| SAE AMS4307C | Aluminum Alloy, Extrusions 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T61511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated |
| SAE AMS4195D | Aluminum Alloy Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024 and 1-1/2% Alclad 2024-T861 Flat Sheet; 1-1/2% Alclad 2024-T861 Plate) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| ASTM B 881 : 2017 : REDLINE | Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products |
| SAE AMS4457 | Aluminum Alloy, Sheet 3.5Cu - 1.1Li - 0.50Mg - 0.40Ag - 0.12Zr (2098-T8) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS4082P | Aluminum Alloy, Seamless Drawn Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS4613A | Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr Solution Heat Treated, Cold Worked (8%) and Precipitation Heat Treated (2219 -T87) |
| SAE AMS4480 | Aluminum Alloy, Seamless Drawn Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4031J | Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-O) Annealed or when specified, “As Fabricated” (2219-F) |
| ASTM B 928 : 2004 | Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service |
| SAE AMS4270C | Aluminum Alloy, Alclad Flat Sheet 4.1Cu - 1.4Mg - 0.45Mn (Alclad 2424-T3) Solution Heat Treated and Cold Worked |
| SAE AMS4086N | Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated, Cold Worked, and Naturally Aged |
| SAE AMS4085D | Aluminum Alloy Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T761) Solution Heat Treated and Overaged |
| SAE AMS4049M | Aluminum Alloy, Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet - T651 Plate) Solution and Precipitation Heat Treated |
| SAE AMS4407A | Aluminum Alloy, Plate (7056-T7651) 9.1Zn - 1.6Cu - 1.9Mg Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4478A | Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T81 Sheet, -T851 Plate) Solution Heat Treated, Cold Worked and Artificially Aged |
| SAE AMS4153L | Aluminum Alloy, Extrusions 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6) Solution and Precipitation Heat Treated |
| SAE AMS4356 | Aluminum Alloy Seamless Drawn Round Tubing 2.3 Cu – 8.0 Zn – 2.0 Mg - 0.16 Zr (7155-T76) Solution Heat Treated and Aged |
| SAE AMS4408A | Aluminum Alloy, Plate (7140-T7651) 6.6Zn - 1.8Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4326A | Aluminum Alloy, 2013, Extruded Bar, Rod, and Profiles 1.0Mg - 0.80Si - 1.8Cu - 0.20Cr (2013 -T6511) Solution Heat Treated, Stress-Relieved by Stretching, and Aged |
| SAE AMS 4305 : 2012 | ALUMINUM ALLOY, EXTRUDED PROFILES (7449-T79511) 8.1ZN - 1.8CU - 2.2MG - 0.16ZR SOLUTION HEAT TREATED, STRESS RELIEVED, AND OVERAGED (COMPOSITION SIMILAR TO UNS A97449) |
| SAE AMS 4279 : 2011 | ALUMINUM ALLOY, ALCLAD SHEET, 4.4CU - 1.5MG - 0.60MN (2024 -T4 FLAT SHEET), SOLUTION HEAT TREATED, HIGH FORMABILITY |
| SAE AMS4087H | Aluminum Alloy Tubing, Seamless, Drawn (2024-0) Reinstate Composition Annealed |
| SAE AMS4123H | Aluminum Alloy, Rolled or Cold Finished Bars and Rods (7075-T651) Solution and Precipitation Heat Treated |
| SAE AMS4156K | Aluminum Alloy, Extrusions 0.68Mg - 0.40Si (6063-T6) Solution and Precipitation Heat Treated |
| SAE AMS4150M | Aluminum Alloy, Extrusions and Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS4201F | Aluminum Alloy Plate 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4337B | Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| SAE AMS4340E | Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged |
| SAE AMS4056H | Aluminum Alloy, Sheet and Plate 4.4Mg - 0.70Mn - 0.15Cr (5083-O) Annealed |
| SAE AMS4402A | Aluminum Alloy, Extruded Profiles (2024-T432) 4.4Cu - 1.5Mg - 0.6Mn Annealed, Stretch Formed, Solution Heat Treated and Stress Relieved by Stretching |
| ASTM B 745/B745M : 2015 : REDLINE | Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains |
| ASTM B 746/B746M : 2016 : REDLINE | Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ANSI H35.1/H35.1M : 2017 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM |
| ASTM B 361 : 2016 : REDLINE | Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings |
| MIL-STD-409 Revision A:1966 | ALLOY NOMENCLATURE AND TEMPER DESIGNATION SYSTEM FOR MAGNESIUM BASE ALLOYS |
| ASTM B 404/B404M : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Condenser and Heat-Exchanger Tubes with Integral Fins (Withdrawn 2006) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.