ASTM B 695 : 2004 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
Hardcopy , PDF
11-11-2021
English
18-11-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 02.05, 2017 Describes the requirements for a coating of zinc mechanically deposited on iron and steel basis metals.
| Committee |
B 08
|
| DevelopmentNote |
Supersedes ASTM B 454 (01/2002)
|
| DocumentType |
Standard
|
| Pages |
6
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the requirements for a coating of zinc mechanically deposited on iron and steel basis metals. The coating is provided in several thicknesses up to and including 107 μm. The seven thickest classes are usually referred to as “mechanically galvanized.”
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:The performance of this coating complies with the requirements of Specification A153/A153M and MIL-C-81562.
1.3The values stated in SI units are to be regarded as the standard. The inch-pound equivalents of SI units are given for informational purposes.
| ASTM A 193/A193M : 2020 | Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications |
| ASTM F 959/F959M : 2017 : REV A | Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series |
| ASTM F 2437/F2437M : 2017 | Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs |
| ASTM A 1105 : 2017 | Standard Specification for Corrugated Steel Manhole Assemblies |
| ASTM F 3125/F3125M : 2019 : EDT 2 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
| ASTM F 3148 : 2017 : REV A | Standard Specification for High Strength Structural Bolt Assemblies, Steel and Alloy Steel, Heat Treated, 144ksi Minimum Tensile Strength, Inch Dimensions |
| ASTM A 761/A761M : 2018 | Standard Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ASTM A 1107/A1107M : 2017 | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Steel Drainage Pipes |
| ASTM F 436/F436M : 2019 | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions |
| ASTM A 760/A760M : 2015 : R2020 | Standard Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains |
| ASTM A 449 : 2014 : R2020 | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use |
| ASTM A 194/A194M : 2020 : REV A | Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
| ASTM F 844 : 2019 | Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use |
| ASTM B 745/B745M : 2015 | Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains |
| ASTM A 563/A563M : 2021 : REV A | Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric) |
| ASTM B 746/B746M : 2016 | Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ASTM F 3329 : 2018 | Standard Specification for Carbon and Alloy Steel Metric Rivets |
| ASTM A 762/A762M : 2019 | Standard Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and Drains |
| ASTM A 307 : 2021 | Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength |
| ASTM B 816 : 2000 : R2021 | Standard Specification for Coatings of Cadmium-Zinc Mechanically Deposited |
| ASTM F 1554 : 2020 | Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength |
| ASTM A 354 : 2017 : EDT 2 | Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners |
| ASTM F 1667 : 2021 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
| ANSI/MSS SP-58:2018 | PIPE HANGERS AND SUPPORTS Materials, Design, Manufacture, Selection, Application, and Installation (ANSI-approved American National Standard) |
| ASTM F 1470 : 2012 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1470 : 2002 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1470 : 2009 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM B 499 : 2009 : R2021 : EDT 1 | Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals |
| ASTM B 762 : 1990 : R2016 | Standard Test Method of Variables Sampling of Metallic and Inorganic Coatings |
| ASTM B 697 : 1988 : R2021 | Standard Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic Coatings |
| ASTM B 697 : 1988 : R2016 | Standard Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic Coatings |
| ASTM B 499 : 2009 : R2014 | Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals |
| ASTM B 762 : 2021 | Standard Guide of Variables Sampling of Metallic and Inorganic Coatings |
| ASTM A 563 : 2015 : REDLINE | Standard Specification for Carbon and Alloy Steel Nuts |
| ASTM B 602 : 1988 : R2016 | Standard Test Method for Attribute Sampling of Metallic and Inorganic Coatings |
| ASTM B 602 : 2021 | Standard Guide for Attribute Sampling of Metallic and Inorganic Coatings |
| ASTM A 563 : 2015 | Standard Specification for Carbon and Alloy Steel Nuts |
| ASTM F 1470 : 2018 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1470 : 2001 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1470 : 2019 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM B 183 : 2018 | Standard Practice for Preparation of Low-Carbon Steel for Electroplating |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.