ASTM B 987/B987M : 2017 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Carbon Fiber Thermoset Polymer Matrix Composite Core (CFC) for use in Overhead Electrical Conductors
Hardcopy , PDF
14-08-2020
English
01-02-2017
Committee |
B 01
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers carbon fiber reinforced thermoset matrix composite core strength members for use in reinforcing or supporting overhead electrical conductors.
1.2This specification covers carbon fiber core diameters from 0.180 to 0.500 in. [4.57 to 12.7 mm], inclusive.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 5423 : 1993 : R2005 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation (Withdrawn 2014) |
ASTM D 5117 : 1996 | Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock |
ASTM D 7028 : 2007 | Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) |
ASTM D 5117 : 2003 | Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock |
ASTM D 3916 : 2002 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod |
ASTM D 3916 : 2008 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod |
ASTM D 3916 : 1994 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod |
ASTM D 5117 : 2017 | Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock |
ASTM D 5117 : 2009 | Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock |
ASTM D 7028 : 2007 : EDT 1 | Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) |
ASTM D 5423 : 1993 : R1999 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
ASTM D 7028 : 2007 : R2015 | Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) |
ASTM D 3916 : 2008 : R2016 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced<brk /> Plastic Rod |
ASTM D 5423 : 2014 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.