
ASTM C 1208/C1208M : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by

Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe Bursting, and Tunnels
Hardcopy , PDF
14-11-2022
English
20-09-2018
This specification establishes the criteria for the manufacture, quality assurance testing, inspection, installation, field acceptance testing, and product marking of vitrified clay jacking pipe to be used in microtunneling, the pilot tube method, sliplining, pipe bursting, and in casings and tunnels for the conveyance of sewage, industrial wastes, and storm water.
Committee |
C 04
|
DocumentType |
Standard
|
Pages |
7
|
ProductNote |
This standard also refer to ASTM D 395,ASTM D 471
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification establishes the criteria for the manufacture, quality assurance testing, inspection, installation, field acceptance testing, and product marking of vitrified clay jacking pipe to be used in microtunneling, the pilot tube method, sliplining, pipe bursting, and in casings and tunnels for the conveyance of sewage, industrial wastes, and storm water.
1.1.1Sections 3 through 7 and 9 of this specification contain manufacturing, quality assurance testing, inspection, and product marking criteria which are applicable to vitrified clay pipe prior to installation.
1.1.2Section 8 of this specification contains criteria for the installation and field acceptance testing of vitrified clay pipe.
1.2This specification also covers materials and test requirements for jointing of the pipe.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 67/C67M : 2021 | Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile |
ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 471 : 2016 : REV A | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM C 1091 : 1999 | Standard Test Method for Hydrostatic Infiltration and Exfiltration Testing of Vitrified Clay Pipe Lines |
ASTM C 1091 : 2003 : REV A : R2022 | Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines (Withdrawn 2024) |
ASTM D 1149 : 2016 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ASTM C 301 : 2018 : R2022 | Standard Test Methods for Vitrified Clay Pipe |
ASTM C 1091 : 2003 : REV A : R2008 | Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines |
ASTM C 896 : 2021 : REV A | Standard Terminology Relating to Clay Products |
ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1149 : 2015 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ASTM C 1091 : 2002 | Standard Test Method for Hydrostatic Infiltration and Exfiltration Testing of Vitrified Clay Pipe Lines |
ASTM D 543 : 2021 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 1149 : 2007 | Standard Test Methods for Rubber Deterioration-Cracking in an Ozone Controlled Environment |
ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 471 : 2016 : REV A : R2021 | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM C 896 : 2021 | Standard Terminology Relating to Clay Products |
ASTM C 828 : 2011 : R2016 | Standard Test Method for Low-Pressure Air Test of Vitrified Clay Pipe Lines |
ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 1149 : 2018 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM C 828 : 1998 | Standard Test Method for Low-Pressure Air Test of Vitrified Clay Pipe Lines |
ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 543 : 2020 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1149 : 2007 : R2012 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1149 : 1978 : REV A | Standard Test Method for Rubber Deterioration - Surface Ozone Cracking In A Chamber ( Flat Specimen) |
ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM C 896 : 2020 : EDT 1 | Standard Terminology Relating to Clay Products |
ASTM C 1091 : 2003 | Standard Test Method for Hydrostatic Infiltration and Exfiltration Testing of Vitrified Clay Pipe Lines |
ASTM C 1091 : 2003 : REV A : R2013 | Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines |
ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM C 828 : 2011 : R2021 | Standard Test Method for Low-Pressure Air Test of Vitrified Clay Pipe Lines |
ASTM C 1091 : 2003 : REV A | Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines |
ASTM C 301 : 2018 | Standard Test Methods for Vitrified Clay Pipe |
ASTM C 1091 : 2003 : REV A : R2018 | Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines |
ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM C 67/C67M : 2020 | Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile |
ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1149 : 1999 | Standard Test Method for Rubber Deterioration-Surface Ozone Cracking in a Chamber |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.