ASTM C 131/C131M : 2020
Current
The latest, up-to-date edition.
Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
Hardcopy , PDF
English
01-04-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
C 09
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers a procedure for testing of coarse aggregates with a maximum size smaller than 37.5 mm ([11/2in.] for resistance to degradation using the Los Angeles testing machine (Note 1).
Note 1:A procedure for testing coarse aggregate larger than 19.0 mm [3/4in.] is covered in Test Method C535. Thus coarse aggregates with a maximum size between 19 mm [3/4in.] and 37.5 mm [11/2in.] may be tested by Test Method C535 or Test Method C131/C131M.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
Note 2:Sieve size is identified by its standard designation in Specification E11. The Alternative designation given in parentheses is for information only and does not represent a different standard sieve size.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM A 6/A6M : 2022 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM C 670 : 2024 | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
| ASTM E 11 : 2024 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 125 : 2024 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM A 6/A6M : 2019 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM A 6/A6M : 2024 : REV A | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM A 6/A6M : 2024 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM A 6/A6M : 2023 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM A 6/A6M : 2021 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM C 670 : 2024 : REV A | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 136 : 1996 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 670 : 2015 | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
| ASTM A 6/A6M : 2024 : REV B | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.