ASTM C 1482 : 2023
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
Hardcopy , PDF
24-04-2024
English
22-03-2023
Committee |
C 16
|
DocumentType |
Standard
|
Pages |
11
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers the composition and physical properties of lightweight, flexible open-cell polyimide foam insulation intended for use as thermal and sound-absorbing insulation for temperatures from –328°F up to +572°F (–200°C and +300°C) in commercial and industrial environments.
1.1.1Annex A1 includes faced polyimide foam as specified by the U.S. Navy for marine applications.
1.1.2This standard is designed as a material specification and not a design document. Physical property requirements vary by application and temperature. No single test is adequate for estimating either the minimum or maximum use temperature of polyimide foam under all possible conditions. Consult the manufacturer for specific recommendations and physical properties for specific applications.
1.1.3The use of an appropriate vapor retarder is required in all applications where condensation could occur and cause a decrease in thermal performance or affect other system properties.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.
Note 1:The subject matter of this material specification is not covered by any other ASTM specification. There is no known ISO standard covering the subject of this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 1594 : 2011 : R2017 | Standard Specification for Polyimide Rigid Cellular Thermal Insulation |
ASTM C 1558 : 2019 | Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation |
ASTM C 1774 : 2013 : R2019 | Standard Guide for Thermal Performance Testing of Cryogenic Insulation Systems |
ASTM C 1558 : 2024 | Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation |
ASTM C 1594 : 2023 | Standard Specification for Polyimide Rigid Cellular Thermal Insulation |
ASTM E 84 : 2023 : REV D | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 96/E96M : 2022 : REV A : EDT 1 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM C 1304 : 2018 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
ASTM E 176 : 2021 : REV A : EDT 1 | Standard Terminology of Fire Standards |
ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM C 390 : 2008 : R2024 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots |
ASTM C 423 : 2022 | Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method |
ASTM E 96/E96M : 2023 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
ASTM E 96/E96M : 2024 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
ASTM E 176 : 2024 | Standard Terminology of Fire Standards |
ASTM C 390 : 2008 : R2019 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots |
ASTM C 1304 : 2023 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
ASTM C 665 : 2023 | Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing |
ASTM E 1354 : 2022 : REV C | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM C 423 : 2023 | Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method |
ASTM E 1354 : 2023 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM C 665 : 2017 | Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing |
ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.