ASTM C 1840/C1840M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Inspection and Acceptance of Installed Reinforced Concrete Culvert, Storm Drain, and Storm Sewer Pipe
Hardcopy , PDF
18-01-2024
English
11-05-2017
CONTAINED IN VOL. 04.05, 2017 Defines the requirements for inspection and acceptance of installed reinforced concrete pipe by either person-entry, or remote inspection.
Committee |
C 13
|
DocumentType |
Standard Practice
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This practice covers the requirements for inspection and acceptance of installed reinforced concrete pipe by either person-entry, or remote inspection as shown in Figs. 1 and 2, respectively.
1.2The scope of this specification is intended for installation related observations and assumes that pre-installation inspection has been completed.
1.3The reinforced concrete culvert, storm drain and storm sewer pipe shall be manufactured in accordance with Specification C76, C506, C507, C655, or C1417 and accepted in accordance with AASHTO R073. This specification shall only be used for gravity, non-pressure storm drainage applications.
1.4Person Entry shall be used unless extenuating circumstances preclude this type inspection. Remote inspection is acceptable for use for pipe diameters of 30 in. [750 mm] and smaller unless otherwise specified by owner or engineer.
1.5Access of installed pipe for manual inspection shall follow OSHA 29 CFR PART 1926 SUBPART AA regulations for confined space entry. However, this standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6This practice does not cover deformation or deflection assessment. Concrete pipe is classified as a rigid structure because they do not bend or deflect appreciably under load before cracking. Due to these facts shape evaluation are of little or no value when evaluating concrete pipe.
1.7The values stated in either Imperial/US or [SI units] are to be regarded separately as standard. The SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
ASTM C 1417 : 2014 : EDT 1 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM D 932 : 2015 : REDLINE | Standard Practice for Filamentous Iron Bacteria in Water and Water-Formed Deposits |
ASTM C 822 : 2021 | Standard Terminology Relating to Concrete Pipe and Related Products |
ASTM C 507 : 2000 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1417 : 2008 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 1417 : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 506 : 2022 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1417 : 2004 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 76 : 2022 : REV A | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1417 : 2002 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM D 932 : 1985 : R1997 | Standard Test Method for Iron Bacteria in Water and Water-Formed Deposits |
ASTM C 76 : 2020 | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1417 : 2014 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 76 : 2022 | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1417 : 2015 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 1417 : 2000 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 822 : 2020 | Standard Terminology Relating to Concrete Pipe and Related Products |
ASTM C 507 : 2020 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
ASTM C 506 : 2000 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
ASTM C 506 : 2022 : REV A | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1417 : 2013 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 1417 : 2015 : REDLINE | SPECIFICATION FOR MANUFACTURE OF REINFORCED CONCRETE SEWER, STORM DRAIN, AND CULVERT PIPE FOR DIRECT DESIGN |
CFR 29(PT1926) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR - SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION |
ASTM C 1417 : 2012 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 1417 : 2011 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 506 : 2020 : EDT 1 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
ASTM C 507 : 2022 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.