ASTM C 207 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Hydrated Lime for Masonry Purposes
Hardcopy , PDF
05-07-2024
English
01-10-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.
This specification covers four types of hydrated lime. Types N and S are suitable for use in mortar, in scratch and brown coats of cement plaster, for stucco, and for addition to portland-cement concrete.
| Committee |
C 07
|
| DocumentType |
Standard
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers four types of hydrated lime. Types N and S are suitable for use in mortar, in scratch and brown coats of cement plaster, for stucco, and for addition to portland-cement concrete. Types NA and SA are air-entrained hydrated limes that are suitable for use in any of the above uses where the inherent properties of lime and air-entrainment are desired. The four types of lime sold under this specification shall be designated as follows:
1.1.1Type N—Normal hydrated lime for masonry purposes.
1.1.2Type S—Special hydrated lime for masonry purposes.
1.1.3Type NA—Normal air-entraining hydrated lime for masonry purposes.
1.1.4Type SA—Special air-entraining hydrated lime for masonry purposes.
Note 1:Type S, special hydrated lime, and Type SA, special air-entraining hydrated lime, are differentiated from Type N, normal hydrated lime, and Type NA, normal air-entraining hydrated lime, principally by their ability to develop high, early plasticity and higher water retentivity, and by a limitation on their unhydrated oxide content.
Note 2:For normal (Type N) and special (Type S) finishing hydrated lime, refer to Specification C206.
Note 3:Some building codes prohibit the use of air-entraining materials in mortar, because of the accompanying reduction in bond and compressive strength. Where increased freeze-thaw resistance is important, air-entraining may be beneficial. Air-entraining lime should not be used as a finishing lime.
Note 4:For lime putty, refer to Specification C1489.
1.2The values stated in SI units are to be regarded as standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1660 : 2010 : R2018 | Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry |
| ASTM C 1707 : 2018 | Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes |
| ASTM D 6684 : 2018 | Standard Specification for Materials and Manufacture of Articulating Concrete Block (ACB) Systems |
| ASTM C 1722 : 2023 | Standard Guide for Repair and Restoration of Dimension Stone |
| ASTM E 1266 : 2020 | Standard Practice for Processing Mixtures of Lime, Fly Ash, and Heavy Metal Wastes in Structural Fills and Other Construction Applications |
| ASTM C 139 : 2022 | Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes |
| ASTM D 3260 : 2001 : R2023 | Standard Test Method for Acid and Mortar Resistance of Factory-Applied Clear Coatings on Extruded Aluminum Products |
| ASTM C 51 : 2021 | Standard Terminology Relating to Lime and Limestone (as Used by the Industry) |
| ASTM C 482 : 2020 | Standard Test Method for Bond Strength of Ceramic Tile to Portland Cement Paste |
| ASTM C 1670/C1670M : 2023 | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
| ASTM C 510 : 2016 : R2022 | Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants |
| ASTM C 936/C936M : 2023 | Standard Specification for Solid Concrete Interlocking Paving Units |
| ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
| ASTM C 1782/C1782M : 2023 | Standard Specification for Segmental Concrete Paving Slabs |
| ASTM C 926 : 2023 | Standard Specification for Application of Portland Cement-Based Plaster |
| ASTM C 476 : 2023 | Standard Specification for Grout for Masonry |
| ASTM C 110 : 2020 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
| ASTM C 1713 : 2023 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
| ASTM C 1782/C1782M : 2023 : REV A | Standard Specification for Segmental Concrete Paving Slabs |
| ASTM C 139 : 2023 | Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes |
| ASTM C 926 : 2024 | Standard Specification for Application of Portland Cement-Based Plaster |
| ASTM C 936/C936M : 2023 : REV A | Standard Specification for Solid Concrete Interlocking Paving Units |
| ASTM C 1670/C1670M : 2023 : REV A | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
| ASTM C 51 : 2023 | Standard Terminology Relating to Lime and Limestone (as Used by the Industry) |
| ASTM C 1489 : 2015 : R2022 | Standard Specification for Lime Putty for Structural Purposes |
| ASTM C 226 : 2019 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM C 226 : 2022 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM C 1489 : 2015 | Standard Specification for Lime Putty for Structural Purposes |
| ASTM C 778 : 2017 | Standard Specification for Standard Sand |
| ASTM C 1489 : 2001 | Standard Specification for Lime Putty for Structural Purposes |
| ASTM C 1489 : 2001 : R2008 : EDT 1 | Standard Specification for Lime Putty for Structural Purposes |
| ASTM C 206 : 2014 | Standard Specification for Finishing Hydrated Lime |
| ASTM C 226 : 1996 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM C 25 : 2019 : EDT 1 | Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime |
| ASTM C 206 : 2014 : R2022 | Standard Specification for Finishing Hydrated Lime |
| ASTM C 110 : 2000 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
| ASTM C 778 : 2021 | Standard Specification for Standard Sand |
| ASTM C 25 : 2019 | Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.