ASTM C 33/C33M : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Concrete Aggregates
Hardcopy , PDF
21-08-2023
English
20-04-2018
Committee |
C 09
|
DocumentType |
Standard
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete.2
1.2This specification is for use by a contractor, concrete supplier, or other purchaser as part of the purchase document describing the material to be furnished.
Note 1:This specification is regarded as adequate to ensure satisfactory materials for most concrete. It is recognized that, for certain work or in certain regions, it may be either more or less restrictive than needed. For example, where aesthetics are important, more restrictive limits may be considered regarding impurities that would stain the concrete surface. The specifier should ascertain that aggregates specified are or can be made available in the area of the work, with regard to grading, physical, or chemical properties, or combination thereof.
1.3This specification is also for use in project specifications to define the quality of aggregate, the nominal maximum size of the aggregate, and other specific grading requirements. Those responsible for selecting the proportions for the concrete mixture shall have the responsibility of determining the proportions of fine and coarse aggregate and the addition of blending aggregate sizes if required or approved.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 1105 : 2017 : R2022 | Standard Specification for Corrugated Steel Manhole Assemblies |
ASTM E 3264 : 2021 | Standard Guide for Homogeneity of Samples and Reference Materials Used for Inter- and Intra-Laboratory Studies |
ASTM C 1364 : 2023 | Standard Specification for Architectural Cast Stone |
ASTM C 654 : 2019 | Standard Specification for Porous Concrete Pipe |
ASTM C 1417M : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric) |
ASTM E 2853/E2853M : 2022 | Standard Test Method for Evaluating Ground Response Robot Capabilities: Search Tasks |
ASTM C 1577 : 2020 : EDT 1 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
ASTM C 505 : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints |
ASTM C 1504 : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains |
ASTM C 470/C470M : 2023 | Standard Specification for Molds for Forming Concrete Test Cylinders Vertically |
ASTM C 14 : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe |
ASTM D 6884 : 2003 : R2015 : EDT 1 | Standard Practice for Installation of Articulating Concrete Block (ACB) Revetment Systems (Withdrawn 2024) |
ASTM C 985M : 2022 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 1903 : 2021 | Standard Specification for Precast Concrete Duct Bank |
ASTM C 915 : 1979 : R2018 | Standard Specification for Precast Reinforced Concrete Crib Wall Members |
ASTM C 14M : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric) |
ASTM C 129 : 2022 | Standard Specification for Nonloadbearing Concrete Masonry Units |
ASTM C 88/C88M : 2018 | Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate |
ASTM C 1581/C1581M : 2018 : REV A | Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage |
ASTM C 719 : 2022 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
ASTM C 845/C845M : 2018 | Standard Specification for Expansive Hydraulic Cement |
ASTM C 858 : 2019 | Standard Specification for Underground Precast Concrete Utility Structures |
ASTM C 118M : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage (Metric) (Withdrawn 2024) |
ASTM E 2991/E2991M : 2017 | Standard Test Method for Evaluating Response Robot Mobility: Traverse Gravel Terrain |
ASTM C 1372 : 2022 | Standard Specification for Dry-Cast Segmental Retaining Wall Units |
ASTM D 8337/D8337M : 2021 | Standard Test Method for Evaluation of Bond Properties of FRP Composite Applied to Concrete Substrate using Single-Lap Shear Test |
ASTM C 412 : 2019 | Standard Specification for Concrete Drain Tile |
ASTM C 1439 : 2019 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
ASTM C 139 : 2022 | Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes |
ASTM C 507M : 2022 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 1786 : 2019 | Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
ASTM C 1319 : 2023 | Standard Specification for Concrete Grid Paving Units |
ASTM D 1079 : 2020 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM C 936/C936M : 2023 | Standard Specification for Solid Concrete Interlocking Paving Units |
ASTM C 1089 : 2019 | Standard Specification for Spun Cast Prestressed Concrete Poles |
ASTM C 1894 : 2022 | Standard Guide for Microbially Induced Corrosion of Concrete Products |
ASTM G 109 : 2023 | Standard Test Methods for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments |
ASTM D 7958/D7958M : 2017 | Standard Test Method for Evaluation of Performance for FRP Composite Bonded to Concrete Substrate using Beam Test |
ASTM C 1782/C1782M : 2023 | Standard Specification for Segmental Concrete Paving Slabs |
ASTM C 87/C87M : 2023 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
ASTM C 1433 : 2020 : EDT 1 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers |
ASTM C 1846/C1846M : 2019 | Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1884 : 2023 | Standard Specification for Manufactured Concrete Ballast Units |
ASTM C 1602/C1602M : 2022 | Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
ASTM C 937 : 2023 | Standard Specification for Grout Fluidifier for Preplaced-Aggregate Concrete |
ASTM D 3517 : 2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe |
ASTM C 1562 : 2010 : R2018 | Standard Guide for Evaluation of Materials Used in Extended Service of Interim Spent Nuclear Fuel Dry Storage Systems |
ASTM C 506M : 2022 : REV A | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 412M : 2019 | Standard Specification for Concrete Drain Tile (Metric) |
ASTM C 1622/C1622M : 2010 : R2016 : EDT 1 | Standard Specification for Cold-Weather Admixture Systems |
ASTM C 1634 : 2023 | Standard Specification for Concrete Facing Brick and Other Concrete Masonry Facing Units |
ASTM C 1623 : 2022 | Standard Specification for Manufactured Concrete Masonry Lintels |
ASTM C 1491 : 2019 | Standard Specification for Concrete Roof Pavers (Withdrawn 2023) |
ASTM C 1818 : 2022 | Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1731 : 2021 | Standard Specification for Concrete Floor Tile |
ASTM C 1492 : 2022 | Standard Specification for Concrete Roof Tile |
ASTM C 981 : 2020 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
ASTM C 478/C478M : 2022 | Standard Specification for Circular Precast Reinforced Concrete Manhole Sections |
ASTM D 1985 : 2013 : R2019 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
ASTM C 226 : 2022 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
ASTM C 979/C979M : 2016 | Standard Specification for Pigments for Integrally Colored Concrete |
ASTM E 488/E488M : 2022 | Standard Test Methods for Strength of Anchors in Concrete Elements |
ASTM C 142/C142M : 2017 | Standard Test Method for Clay Lumps and Friable Particles in Aggregates |
ASTM D 1863/D1863M : 2005 : R2018 | Standard Specification for Mineral Aggregate Used on Built-Up Roofs |
ASTM C 655M : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 1776/C1776M : 2017 : R2022 | Standard Specification for Wet-Cast Precast Modular Retaining Wall Units |
ASTM C 685/C685M : 2017 | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
ASTM C 505M : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric) |
ASTM C 985 : 2022 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe |
ASTM C 404 : 2018 | Standard Specification for Aggregates for Masonry Grout |
ASTM D 7913/D7913M : 2014 : R2020 | Standard Test Method for Bond Strength of Fiber-Reinforced Polymer Matrix Composite Bars to Concrete by Pullout Testing |
ASTM C 76M : 2022 : REV A | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 654M : 2019 | Standard Specification for Porous Concrete Pipe (Metric) |
ASTM D 6825 : 2021 | Standard Guide for Placement of Riprap Revetments |
ASTM C 118 : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage |
ASTM C 507 : 2022 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
ASTM C 361 : 2022 | Standard Specification for Reinforced Concrete Low-Head Pressure Pipe |
ASTM C 506 : 2022 : REV A | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
ASTM C 913 : 2021 | Standard Specification for Precast Concrete Water and Wastewater Structures |
ASTM C 1803 : 2020 | Standard Guide for Abrasion Resistance of Mortar Surfaces Using a Rotary Platform Abraser |
ASTM A 1081/A1081M : 2021 | Standard Test Method for Evaluating Bond of Seven-Wire Steel Prestressing Strand |
ASTM C 40/C40M : 2020 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
ASTM C 1932 : 2023 | Standard Specification for Manufacture of Reinforced Precast Concrete End Sections for Pipe |
ASTM C 465 : 2023 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
ASTM C 935 : 2019 | Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast |
ASTM D 5139 : 2019 | Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants |
ASTM C 55 : 2022 | Standard Specification for Concrete Building Brick |
ASTM C 1504M : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric) |
ASTM C 1293 : 2020 : REV A | Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
ASTM D 6783 : 2005 : REV A : R2022 | Standard Specification for Polymer Concrete Pipe |
ASTM C 898/C898M : 2009 : R2017 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course |
ASTM D 6684 : 2018 | Standard Specification for Materials and Manufacture of Articulating Concrete Block (ACB) Systems |
ASTM C 1837 : 2022 | Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures |
ASTM C 1417 : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 1804 : 2020 | Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles |
ASTM C 655 : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe |
ASTM C 884/C884M : 2023 | Standard Test Method for Thermal Compatibility Between Concrete and an Epoxy-Resin Overlay |
ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
ASTM C 1670/C1670M : 2023 | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
ASTM C 295/C295M : 2019 | Standard Guide for Petrographic Examination of Aggregates for Concrete |
ASTM C 1433M : 2022 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric) |
ASTM C 76 : 2022 : REV A | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 233/C233M : 2018 | Standard Test Method for Air-Entraining Admixtures for Concrete |
ASTM C 1613 : 2022 | Standard Specification for Precast Concrete Gravity Grease Interceptor Tanks |
ASTM C 90 : 2022 | Standard Specification for Loadbearing Concrete Masonry Units |
ASTM C 1305/C1305M : 2016 | Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane |
ASTM C 94/C94M : 2023 | Standard Specification for Ready-Mixed Concrete |
ASTM D 2925 : 2014 : R2019 | Standard Test Method for Beam Deflection of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe Under Full Bore Flow |
ASTM C 361M : 2022 | Standard Specification for Reinforced Concrete Low-Head Pressure Pipe (Metric) |
ASTM C 330/C330M : 2023 | Standard Specification for Lightweight Aggregates for Structural Concrete |
ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
ACI PRC 506.5:2022 | Specifying Underground Shotcrete - Guide |
ICC IBC INTERNATIONAL BUILDING CODE:2021 | International Building Code |
ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM C 40/C40M : 2011 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
ASTM D 422 : 1963 : R2007 : EDT 1 | Standard Test Method for Particle-Size Analysis of Soils |
ASTM C 1778 : 2019 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM C 331/C331M : 2017 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
ASTM C 1778 : 2016 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM C 40/C40M : 2019 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 331/C331M : 2023 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
ASTM C 332 : 2017 | Standard Specification for Lightweight Aggregates for Insulating Concrete |
ASTM D 3665 : 2012 : R2017 | Standard Practice for Random Sampling of Construction Materials |
ASTM C 332 : 2023 | Standard Specification for Lightweight Aggregates for Insulating Concrete |
ASTM D 3665 : 2007 | Standard Practice for Random Sampling of Construction Materials |
ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM C 87/C87M : 2017 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
ASTM D 75/D75M : 2009 | Standard Practice for Sampling Aggregates |
ASTM C 87/C87M : 2023 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
ASTM C 136/C136M : 2014 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
ASTM C 1778 : 2022 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM C 1778 : 2014 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM D 75/D75M : 2014 | Standard Practice for Sampling Aggregates |
ASTM D 2419 : 1995 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 123/C123M : 2014 | Standard Test Method for Lightweight Particles in Aggregate (Withdrawn 2023) |
ASTM C 666/C666M : 2015 | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Withdrawn 2024) |
ASTM C 330/C330M : 2023 | Standard Specification for Lightweight Aggregates for Structural Concrete |
ASTM C 1778 : 2019 : REV A | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM C 1778 : 2020 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 330/C330M : 2017 : REV A | Standard Specification for Lightweight Aggregates for Structural Concrete |
ASTM D 2419 : 2022 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 2419 : 2014 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 3665 : 1999 | Standard Practice for Random Sampling of Construction Materials |
ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.