Skip to content
Please enter a keyword to search

  • ASTM C 898/C898M : 2009 : R2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-04-2024

    Language(s):  English

    Published date:  14-12-2017

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 06.03, 2017 Specifies the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the criteria in Specification C 836, in a waterproofing system subject to hydrostatic pressure for building decks over occupied space where the membrane is covered with a separate protective wearing course.

    Scope - (Show below) - (Hide below)

    1.1This guide describes the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the criteria in Specification C836/C836M, in a waterproofing system subject to hydrostatic pressure for building decks over occupied space where the membrane is covered with a separate protective wearing course.

    1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee D 08
    Development Note Supersedes ASTM C 898. (07/2009)
    Document Type Guide
    Product Note Reconfirmed 2017
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 7492/D7492M : 2016 : REV A : R2024 Standard Guide for Use of Drainage System Media with Waterproofing Systems
    ASTM D 8463/D8463M : 2023 Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric, Silyl-Terminated Polymer Based Waterproofing Membrane for Use with Separate Wearing Course
    ASTM E 2266 : 2022 Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 1752 : 1967 Standard Specifications For Preformed Expansion Joint Fillers For Concrete Paving And Structural Construction1 Nonextruding And Resilient Nonbituminous Types
    ACI 301 : 2016 SPECIFICATIONS FOR STRUCTURAL CONCRETE
    ASTM C 1193 : 2011 : REV A Standard Guide for Use of Joint Sealants
    ASTM D 1751 : 2004 : R2013 : EDT 1 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)
    ASTM C 1471/C1471M : 2005 : R2014 : EDT 1 Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
    ASTM D 5295 : 2000 Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
    ASTM C 33/C33M : 2023 Standard Specification for Concrete Aggregates
    ASTM C 1193 : 2016 : R2023 Standard Guide for Use of Joint Sealants
    ASTM D 1056 : 2007 Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber
    ASTM C 1472 : 2016 : REDLINE Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM C 1472 : 2005 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM C 1193 : 2016 Standard Guide for Use of Joint Sealants
    ASTM D 1752 : 2004 Standard Specification for Preformed Sponge Rubber and Cork Expansion Joint Fillers for Concrete Paving and Structural Construction
    ASTM C 33/C33M : 2018 Standard Specification for Concrete Aggregates
    ASTM C 1472 : 2010 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM D 1752 : 2004 : REV A : R2013 Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
    ASTM D 1751 : 1999 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)
    ASTM C 836/C836M : 2018 Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course
    ASTM C 1472 : 2006 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM C 1193 : 2005 : REV A Standard Guide for Use of Joint Sealants
    ASTM C 1472 : 2016 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM D 1752 : 2004 : REV A : R2008 Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
    ASTM D 1056 : 1968 : EDT 1 Standard Specification for Sponge and Expanded Cellular Rubber Products
    ASTM D 5957 : 1998 : R2005 Standard Guide for Flood Testing Horizontal Waterproofing Installations
    ASTM D 6506 : 2001 Standard Specification for Asphalt Based Protection for Below-Grade Waterproofing
    ASTM C 1193 : 2016 : REDLINE Standard Guide for Use of Joint Sealants
    ASTM D 5295 : 2000 : R2006 Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
    ASTM D 1056 : 2000 Standard Specification for Flexible Cellular Materials-Sponge or Expanded Rubber
    ASTM D 1751 : 2023 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)
    ASTM C 578 : 2019 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
    ASTM D 1751 : 2018 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)
    ASTM D 6451/D6451M : 1999 : R2021 Standard Guide for Application of Asphalt-Based Protection Board
    ASTM C 1193 : 2012 Standard Guide for Use of Joint Sealants
    ASTM E 1907 : 2006 : REV A Standard Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings (Withdrawn 2008)
    ASTM C 1299 : 1999 Standard Guide for Use in Selection of Liquid-Applied Sealants
    ASTM D 6134 : 1997 Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems
    ASTM C 1472 : 2016 : R2022 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM C 1193 : 2005 Standard Guide for Use of Joint Sealants
    ASTM C 1471 : 2005 Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
    ASTM E 1907 : 2004 Standard Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings
    ASTM D 1751 : 2004 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)
    ASTM D 1752 : 2018 Standard Specification for Preformed Sponge Rubber, Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
    ASTM D 6451/D6451M : 1999 : R2014 : EDT 1 Standard Guide for Application of Asphalt Based Protection Board
    ASTM C 578 : 2022 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
    ASTM D 1751 : 2004 : R2008 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)
    ASTM D 6134 : 2007 : R2013 Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems
    ASTM D 5957 : 1998 : R2013 Standard Guide for Flood Testing Horizontal Waterproofing Installations
    ASTM D 1752 : 2018 : R2023 Standard Specification for Preformed Sponge Rubber, Cork, and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
    ASTM D 6451 : 1999 Standard Guide for Application of Asphalt Based Protection Board
    ASTM D 5957 : 1998 : R2021 Standard Guide for Flood Testing Horizontal Waterproofing Installations
    ASTM C 1193 : 2000 Standard Guide for Use of Joint Sealants
    ASTM D 1056 : 2014 Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber
    ASTM D 6506 : 2001 : R2009 Standard Specification for Asphalt Based Protection for Below-Grade Waterproofing
    ASTM D 1056 : 2014 : REDLINE Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber
    ASTM C 1471/C1471M : 2005 : R2021 Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
    ASTM C 1471/C1471M : 2022 Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
    ASTM E 1907 : 1997 Standard Practices for Determining Moisture-Related Acceptability of Concrete Floors to Receive Moisture-Sensitive Finishes
    ASTM D 5957 : 1998 Standard Guide for Flood Testing Horizontal Waterproofing Installations
    ASTM C 1299 : 2003 Standard Guide for Use in Selection of Liquid-Applied Sealants (Withdrawn 2012)
    ASTM C 1472 : 2016 : EDT 1 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM C 578 : 2023 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
    ASTM C 1193 : 2011 Standard Guide for Use of Joint Sealants
    ASTM C 1472 : 2000 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
    ASTM C 1193 : 2013 Standard Guide for Use of Joint Sealants
    ASTM D 1752 : 1984 : R1996 : EDT 1 Standard Specification for Preformed Sponge Rubber and Cork Expansion Joint Fillers for Concrete Paving and Structural Construction
    ASTM E 1907 : 2006 Standard Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings
    ASTM C 836/C836M : 2018 : R2022 Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course
    ASTM D 6134 : 2007 Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems
    ASTM D 1752 : 2004 : REV A Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
    ASTM C 1193 : 2009 Standard Guide for Use of Joint Sealants
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective