ASTM C 647 : 2008 : R2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
Hardcopy , PDF
12-04-2019
English
01-11-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.06, 2014 Describes properties of mastics and coating finishes characterizing their performance as finishes for thermal insulation.
| Committee |
C 16
|
| DocumentType |
Guide
|
| Pages |
6
|
| ProductNote |
Reconfirmed 2013
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide identifies properties of mastics and coating finishes characterizing their performance as finishes for thermal insulation.
1.2These properties relate to application and service. Each property is defined, and its significance and suggested test methods are described.
1.3The properties appear in the following order in this guide.
| Paragraph | |
| Application Properties | 6 |
| Consistency | 6.1 |
| Coverage | 6.2 |
| Build | 6.3 |
| Wet Flammability | 6.4 |
| Toxicity | 6.5 |
| Temperature and Humidity Range | 6.6 |
| Surface Wetting and Adhesion | 6.7 |
| Gap Filling and Bridging | 6.8 |
| Sizing and Sealing | 6.9 |
| Corrosion or Solvent Attack | 6.10 |
| Drying Time and Curing Time | 6.11 |
| Shrinkage | 6.12 |
| Storage Stability | 6.13 |
| Freeze-Thaw Stability | 6.14 |
| Service Properties | 7 |
| Specimen Preparation | 7.1 |
| Outdoor Durability | 7.2 |
| Environmental Resistance | 7.3 |
| Temperature Limits | 7.3.1 |
| Chemicals and Water Resistance | 7.3.2 |
| Mold and Mildew Resistance | 7.3.3 |
| Surface Flammability | 7.4 |
| Water-Vapor Transmission Rate | 7.5 |
| Adhesion | 7.6 |
| Damage Resistance | 7.7 |
| Impact Resistance | 7.7.1 |
| Abrasion Resistance | 7.7.2 |
| Stress Resistance | 7.8 |
| Flexure | 7.8.1 |
| Elongation | 7.8.2 |
| Color | 7.9 |
| Odor | 7.10 |
| Other Properties | 8 |
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
| ASTM E 96/E96M : 2016 : REDLINE | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM D 529 : 2004 | Standard Practice for Enclosed Carbon-Arc Exposures of Bituminous Materials (Withdrawn 2013) |
| ASTM D 1729 : 2016 : REDLINE | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM C 639 : 2015 : REDLINE | Standard Test Method for Rheological (Flow) Properties of Elastomeric Sealants |
| ASTM G 21 : 2015 : REDLINE | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
| ASTM D 2354 : 2010 | Standard Test Method for Minimum Film Formation Temperature (MFFT) of Emulsion Vehicles |
| ASTM D 543 : 2014 : REDLINE | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D 1310 : 2014 : REDLINE | Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus |
| ASTM D 562 : 2010 | Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer |
| ASTM D 2939 : 2003 | Standard Test Methods for Emulsified Bitumens Used as Protective Coatings (Withdrawn 2012) |
| ASTM D 3134 : 2015 : REDLINE | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 2444 : 1999 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 2453 : 2015 : REDLINE | Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| ASTM C 792 : 2015 : REDLINE | Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants |
| ASTM C 488 : 2016 : REDLINE | Standard Test Method for Conducting Exterior Exposure Tests of Finishes for Thermal Insulation |
| ASTM G 23 : 1996 | Practice for Operating Light-Exposure Apparatus (Carbon-Arc Type) With and Without Water for Exposure of Nonmetallic Materials (Withdrawn 2000) |
| ASTM D 1823 : 2016 : REDLINE | Standard Test Method for Apparent Viscosity of Plastisols and Organosols at High Shear Rates by Extrusion Viscometer |
| ASTM D 658 : 1991 | Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996) |
| ASTM E 659 : 2015 : REDLINE | Standard Test Method for Autoignition Temperature of Chemicals |
| ASTM C 733 : 1993 | Standard Test Method for Volume Shrinkage of Latex Sealants (Withdrawn 2000) |
| ASTM D 1824 : 2016 : REDLINE | Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates |
| ASTM E 162 : 2016 : REDLINE | Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM C 461 : 2017 : REDLINE | Standard Test Methods for Mastics and Coatings Used With Thermal Insulation |
| ASTM C 168 : 2017-06 | TERMINOLOGY RELATING TO THERMAL INSULATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.