• There are no items in your cart

ASTM D 1331 : 2020

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials

Available format(s)

Hardcopy , PDF

Superseded date

01-07-2024

Language(s)

English

Published date

01-12-2020

€67.30
Excluding VAT

Committee
D 01
DocumentType
Test Method
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1These test methods cover the determination of surface tension and interfacial tension of a variety of liquid materials, including but not restricted to paints, solvents, and solutions of surface-active agents, as defined in Terminology D459. Four methods are covered as follows:

Method A—Surface Tension by du Noüy ring;

Method B—Interfacial Tension by du Noüy ring;

Method C—Surface Tension by Wilhelmy plate; and

Method D—Interfacial Tension by Wilhelmy plate.

1.2Method A originally was written primarily to cover aqueous solutions of surface-active agents, but is also applicable to aqueous paints, nonaqueous solutions (including paints) and mixed solvent solutions.

1.3Method B is applicable to two-phase solutions. More than one solute component may be present, including solute components that are not in themselves surface-active.

1.4Method C is applicable to surface active liquids and, unlike du Noüy ring, no buoyancy corrections are needed and results are not affected by moderate viscosities (1-10 Pa-sec) of the liquid. It is the recommended method for use with paints and resin solutions.

1.5Method D is applicable to two-phase solutions and mixtures.

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 1359/F1359M : 2022 Standard Test Method for Liquid Penetration Resistance of Protective Clothing or Protective Ensembles Under a Shower Spray While on a Manikin
ASTM D 6469 : 2024 Standard Guide for Microbial Contamination in Fuels and Fuel Systems
ASTM D 8506 : 2023 Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems
ASTM F 1670/F1670M : 2024 Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood
ASTM F 1671/F1671M : 2022 Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System
ASTM D 7826 : 2023 : REV B Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives
ASTM F 2161 : 2021 Standard Guide for Instrument and Precision Bearing Lubricants—Part 1 Oils
ASTM F 1862/F1862M : 2024 Standard Test Method for Resistance of Medical Face Masks to Penetration by Synthetic Blood (Horizontal Projection of Fixed Volume at a Known Velocity)
ASTM D 1417 : 2016 : R2021 Standard Test Methods for Rubber Latices—Synthetic
ASTM F 1819 : 2019 Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood Using a Mechanical Pressure Technique
ASTM D 4751 : 2021 : REV A Standard Test Methods for Determining Apparent Opening Size of a Geotextile
ASTM D 4054 : 2023 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives

ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.