ASTM D 1552 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
Hardcopy , PDF
11-11-2014
English
01-12-2008
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2008
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers three procedures for the determination of total sulfur in petroleum products including lubricating oils containing additives, and in additive concentrates. This test method is applicable to samples boiling above 177°C (350°F) and containing not less than 0.06 mass % sulfur. Two of the three procedures use iodate detection; one employing an induction furnace for pyrolysis, the other a resistance furnace. The third procedure uses IR detection following pyrolysis in a resistance furnace.
1.2 Petroleum coke containing up to 8 mass % sulfur can be analyzed.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 6376 : 2010 : R2017 : EDT 1 | Standard Test Method for Determination of Trace Metals in Petroleum Coke by Wavelength Dispersive X-ray Fluorescence Spectroscopy |
| ASTM E 1418 : 2016 | Standard Practice for Visible Penetrant Testing Using the Water-Washable Process |
| ASTM D 3238 : 2017 : REV A | Standard Test Method for Calculation of Carbon Distribution and Structural Group Analysis of Petroleum Oils by the n-d-M Method |
| ASTM D 1266 : 2018 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM E 1208 : 2016 | Standard Practice for Fluorescent Liquid Penetrant Testing Using the Lipophilic Post-Emulsification Process |
| ASTM D 6969 : 2017 | Standard Practice for Preparation of Calcined Petroleum Coke Samples for Analysis |
| ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 6443 : 2014 : R2019 : EDT 1 | Standard Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure) |
| ASTM D 240 : 2017 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter |
| ASTM D 8056 : 2018 | Standard Guide for Elemental Analysis of Crude Oil |
| ASTM D 3338/D3338M : 2009 : R2014 : EDT 2 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
| ASTM E 1209 : 2018 | Standard Practice for Fluorescent Liquid Penetrant Testing Using the Water-Washable Process |
| ASTM E 1219 : 2016 | Standard Practice for Fluorescent Liquid Penetrant Testing Using the Solvent-Removable Process |
| ASTM D 7455 : 2019 | Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis |
| ASTM D 4868 : 2017 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM E 1210 : 2016 | Standard Practice for Fluorescent Liquid Penetrant Testing Using the Hydrophilic Post-Emulsification Process |
| ASTM D 7578 : 2018 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM E 1220 : 2016 | Standard Practice for Visible Penetrant Testing Using Solvent-Removable Process |
| ASTM D 4951 : 2014 | Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
| ASTM D 396 : 2019 | Standard Specification for Fuel Oils |
| ASTM E 165/E165M : 2018 | Standard Practice for Liquid Penetrant Testing for General Industry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.