ASTM D 1710 : 2015 : REDLINE
Current
The latest, up-to-date edition.
Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes
English
01-09-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.01, 2015 Defines extruded polytetrafluoroethylene (PTFE) rod, heavy-walled tubing, and basic shapes manufactured from the PTFE resin of Specification D 4894 and reprocessed PTFE resin (as defined in Guides D 5033 and D 7209).
| Committee |
D 20
|
| DevelopmentNote |
Supersedes MIL P 22296 (07/2004)
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers extruded polytetrafluoroethylene (PTFE) rod, heavy-walled tubing, and basic shapes manufactured from the PTFE resin of Specification D4894 and reprocessed PTFE resin (as defined in Guide D7209).
1.2The specification covers all sizes of rod, tubing, and basic shapes with a wall thickness of 1.6 mm (1/16in.) or greater. These materials must be made wholly from PTFE and produced in accordance with good commercial ram extrusion practices.
Note 1:This specification and ISO/DIS 13000-1 (1997) and ISO/DIS 13000-2 (1997) differ in approach, however, data obtained using either are technically equivalent.
Note 2:For compression molded PTFE materials, see Specification D3294. Material that can be certified to Specification D3294 may be substituted for Specification D1710, however the reverse in not true.
1.3The values stated in SI units, as detailed in IEEE/ASTM SI 10 are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only.
1.4The following precautionary caveat pertains to the test methods portion, Section 12, only of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-N-85615-10 Base Document:1989 | Nut, Self-Sealing, Self-Locking, CRES, 160 KSI FTU, 250 Deg. F and 450 Deg. F |
| MS75093 Revision B:2013 | Adapter, Connector, Series BNC Socket Contact to GR-874 Hermorphroditic |
| MIL-DTL-39024-14 Revision C:2008 | CONNECTORS, ELECTRICAL, TEST POINT TYPE, PANEL TYPE; SINGLE TEST POINT SUBMINIATURE (PUSH-IN), LOW VOLTAGE, .080 |
| MIL-M-38527 Revision D:1992 | MOUNTING PADS, ELECTRICAL-ELECTRONIC COMPONENT, GENERAL SPECIFICATION FOR |
| MIL-DTL-39024-15 Revision C:2008 | CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; SINGLE TEST POINT, LOW VOLTAGE, .080 |
| MIL-DTL-83502-5 Revision D:2004 | Sockets Plug-In Electronic Components, Round Style (R052) |
| ASTM F 754 : 2008 | Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders |
| MIL-DTL-87104 Revision C:2014 | COAXIAL ASSEMBLIES, GENERAL SPECIFICATION FOR |
| MIL-DTL-15370 Revision K:2015 | COUPLERS, DIRECTIONAL, GENERAL SPECIFICATION FOR |
| MIL-T-55155 Revision C:1993 | TERMINALS, FEEDTHRU (INSULATED) AND TERMINALS, STUD (INSULATED AND NONINSULATED), GENERAL SPECIFICATION FOR |
| MIL-DTL-28837 Revision D:2015 | MIXER STAGES, RADIO FREQUENCY GENERAL SPECIFICATION FOR |
| MIL-DTL-3933-27 Base Document:2004 | ATTENUATORS, FIXED, COAXIAL LINE (SMP CONNECTORS - SMP FULL DETENT MALE TO SMP FULL DETENT MALE), FREQUENCY RANGE: DC TO 18 GHZ |
| MIL C 15370 : F | COUPLERS, DIRECTIONAL GENERAL SPECIFICATION FOR |
| EN ISO 13000-1:2005 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005) |
| ASTM F 754 : 2008 : R2015 | Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders |
| I.S. EN ISO 13000-1:2006 | PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION |
| MIL PRF 83502 : C | SOCKETS, PLUG-IN ELECTRONIC COMPONENTS, ROUND STYLE, GENERAL SPECIFICATION FOR |
| MIL-DTL-83502-2 Revision G:2004 | Sockets Plug-In Electronic Components, Round Style (T05, Press to Fit) |
| MIL-N-85615-8 Base Document:1989 | Nut, Self-Sealing, Self-Locking, Alloy Steel, 125 KSI FTU, 250 Deg. F and 450 Deg. F |
| MIL-DTL-2 Revision G:2006 | VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR |
| ASTM D 3295 : 2015 : REDLINE | Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing |
| BS EN ISO 13000-1:2005 | Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Requirements and designation |
| ISO 13000-1:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation |
| MIL-DTL-83502-1 Revision G:2004 | Sockets Plug-In Electronic Components, Round Style (T07, Low Profile) |
| MIL-DTL-3933-28 Base Document:2004 | ATTENUATORS, FIXED, COAXIAL LINE (SMP CONNECTORS - SMP FULL DETENT MALE TO SMP FULL DETENT MALE), 0 DB, FREQUENCY RANGE: DC TO 18 GHZ |
| MIL-DTL-32385 Base Document:2011 | CONNECTOR, RECEPTACLES, PLUGS, ADAPTER, USED ON ELECTROLUMINESCENT, EMBEDDED, AND PRINTED CIRCUIT BOARD LAMP LIGHTING PANELS |
| 04/30091874 DC : DRAFT FEB 2004 | BS EN ISO 13000-1 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION |
| MIL-DTL-83502 Revision E:2007 | Sockets, Plug-in Electronic Components, Round Style, General Specification for |
| MIL-DTL-1189 Revision E:2018 | VALVE, GATE, BRONZE |
| MIL-DTL-83502-3 Revision E:2004 | Sockets Plug-In Electronic Components, Round Style (T08) |
| MIL-DTL-28875 Revision C:2012 | Amplifiers, Radio-Frequency and Microwave, Solid-State, General Specification for |
| MIL-DTL-3643 Revision B:2003 | Connectors, Coaxial, Radio Frequency, Series HN, and Associated Fittings, General Specification for |
| DIN EN ISO 13000-1:2006-02 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005) |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 7209 : 2006 | Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ISO 13000-1:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation |
| ISO 13000-2:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 2: Preparation of test specimens and determination of properties |
| ASTM D 374 : 1999 | Standard Test Methods for Thickness of Solid Electrical Insulation |
| ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.