ASTM D 1895 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials
23-09-2024
English
01-09-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.01, 2017 Describes the measurement of apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders.
| Committee |
D 20
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1These test methods cover the measurement of apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. Different procedures are given for application to the various forms of these materials that are commonly encountered, from fine powders and granules to large flakes and cut fibers.
1.2The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:Test Method A is equivalent to ISO Method R 60 as described in the appendix. Test Method C is identical with ISO Method R 61.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6881/D6881M : 2003 : R2008 : EDT 1 | Standard Classification for Standard Plastics Industry Bulk Box/Pallet Unit Size Classified By Bulk Density |
| MIL-PRF-24667 Revision C:2008 | COATING SYSTEM, NON-SKID, FOR ROLL, SPRAY, OR SELF-ADHERING APPLICATION |
| DOD-D-51524 Base Document:1986 | DYE, DISPERSE BLUE 3 (METRIC) |
| ASTM D 1457 : 1992 | Specification for Polytetrafluorethylene (PTFE) Molding and Extrusion Materials (Withdrawn 1996) |
| 16/30338304 DC : 0 | BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS |
| MIL-DTL-51522 Revision A:2010 | DYE, DISPERSE RED 11 (METRIC) |
| MIL-S-14374 Revision C:1983 | SILICA GEL, IRON FREE |
| DOD-D-51486 Revision A:1986 | DYE MIX, GREEN SMOKE 7 |
| ASTM E 1099 : 1996 | Standard Specification for Soda Ash, Anhydrous (Sodium Carbonate, Anhydrous) (Withdrawn 2001) |
| ASTM D 3214 : 1996 | Standard Test Methods for Coating Powders and Their Coatings Used for Electrical Insulation (Withdrawn 2002) |
| DOD D 51485 : A | DYE, SOLVENT YELLOW 33 (METRIC) |
| MIL-DTL-3691 Revision E:2006 | DYE MIX, VIOLET |
| ASTM D 704 : 1999 | Standard Specification for Melamine-Formaldehyde Molding Compounds |
| MIL-D-3718 Revision C:1986 | DYE MIX, DISPERSE RED 9 - DEXTRIN (METRIC) |
| ASTM D 704 : 1999 : R2012 | Standard Specification for Melamine-Formaldehyde Molding Compounds |
| ASTM D 704 : 1999 : R2004 | Standard Specification for Melamine-Formaldehyde Molding Compounds |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| SAE AMS3753C | Microspheres, Carbon Hollow |
| ASTM D 2474 : 1992 | Specification for Vinyl Chloride Copolymer Resins (Withdrawn 1999) |
| MIL-D-20550 Revision B:1968 | DIATOMACEOUS EARTH |
| MIL-DTL-51523 Revision A:2010 | DYE, SOLVENT RED 1 (METRIC) |
| ASTM D 3451 : 2006 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 6881 : 2003 | Standard Classification for Standard Plastics Industry Bulk Box/Pallet Unit Size Classified By Bulk Density |
| MIL-M-46891 Revision A:1980 | MOLDING COMPOUND, PHENOLIC RESIN, ASBESTOS REINFORCED |
| MIL-DTL-3284 Revision F:2006 | Dye, Disperse Red 9 |
| ASTM D 6881/D6881M : 2003 : R2013 | Standard Classification for Standard Plastics Industry Bulk Box/Pallet Unit Size Classified By Bulk Density |
| MIL-DTL-51485 Revision B:2006 | DYE, SOLVENT YELLOW 33 |
| DOD D 51522 : 0 | DYE, DISPERSE RED 11 (METRIC) |
| ASTM D 3451 : 2006 : R2012 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 1755 : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) Resins |
| MIL-T-50036 Revision B:1992 | TALC, TECHNICAL, T1 AND T3 |
| MIL-DTL-3277 Revision F:2006 | Dye, Solvent Green 3 |
| MIL-DTL-3668 Revision E:2006 | Dye, 1,4-Diamino-2,3-Dihydroanthraquinone (Blue) |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ISO 60:1977 | Plastics — Determination of apparent density of material that can be poured from a specified funnel |
| ISO 61:1976 | Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.