ASTM D 1896/D1896M : 2010 : R2017
Current
The latest, up-to-date edition.
Standard Practice for Transfer Molding Test Specimens of Thermosetting Compounds
Hardcopy , PDF
English
01-05-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.01, 2017 Defines a general procedure for the transfer molding of mechanical and electrical test specimens of thermosetting molding materials.
| Committee |
D 20
|
| DevelopmentNote |
Supersedes ASTM D 1896. (09/2010)
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1This practice covers a general procedure for the transfer molding of mechanical and electrical test specimens of thermosetting molding materials.
Note 1:The utility of this practice has been demonstrated for the molding of thermosetting molding compounds exhibiting intermediate viscosity non-Newtonian flow.
1.2The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system are not always exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems can result in nonconformance with this practice.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
| ASTM D 957 : 2012 : REDLINE | Standard Practice for Determining Surface Temperature of Molds for Plastics |
| ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
| ASTM D 3795 : 2000 : REV A : R2006 | Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 3795 : 2000 : REV A : R2012 | Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer |
| ASTM D 3795 : 2020 | Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer |
| ASTM D 3123 : 1998 : R1999 : EDT 1 | Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds |
| ASTM D 3123 : 2009 : R2017 | Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds |
| ASTM D 3123 : 1998 : R2004 | Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds |
| ASTM D 3123 : 2009 | Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds |
| ASTM D 3795 : 2000 : REV A | Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.