• Shopping Cart
    There are no items in your cart

ASTM D 2609 : 2021

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

Available format(s)

Hardcopy , PDF

Superseded date

26-04-2024

Superseded by

ASTM D 2609 : 2024

Language(s)

English

Published date

20-04-2021

€59.22
Excluding VAT

Committee
F 17
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers plastic insert fittings for polyethylene (PE) plastic pipe, and also PVC insert fittings for PE to PVC pipe transitions. Included are requirements for materials, workmanship, dimensions, and burst pressure.

1.2The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 645 : 2018 : REV B Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

ASTM D 256 : 2010 : R2018 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 2239 : 2022 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 256 : 2023 : EDT 1 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 2466 : 2023 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
ASTM D 256 : 2023 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 2466 : 2021 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 2239 : 2021 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
ASTM D 2239 : 2012 : REV A : R2020 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.