• Shopping Cart
    There are no items in your cart

ASTM D 2622 : 2024

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry

Available format(s)

Hardcopy , PDF

Superseded date

19-12-2024

Language(s)

English

Published date

01-07-2024

€74.48
Excluding VAT

Committee
D 02
DocumentType
Test Method
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method covers the determination of total sulfur in petroleum and petroleum products that are single-phase and either liquid at ambient conditions, liquefiable with moderate heat, or soluble in hydrocarbon solvents. These materials can include diesel fuel, jet fuel, kerosene, other distillate oil, naphtha, residual oil, lubricating base oil, hydraulic oil, crude oil, unleaded gasoline, gasoline-ethanol blends, and biodiesel.

1.2The range of this test method is between the PLOQ value (calculated by procedures consistent with Practice D6259) of 3 mg/kg total sulfur and the highest level sample in the round robin, 4.6 % by weight total sulfur.

Note 1:Instrumentation covered by this test method can vary in sensitivity. The applicability of the test method at sulfur concentrations below 3 mg/kg may be determined on an individual basis for WDXRF instruments capable of measuring lower levels, but precision in this test method does not apply.

1.2.1The values of the limit of quantitation (LOQ) and method precision for a specific laboratory’s instrument depends on instrument source power (low or high power), sample type, and the practices established by the laboratory to perform the method.

1.3Samples containing more than 4.6 % by mass sulfur should be diluted to bring the sulfur concentration of the diluted material within the scope of this test method. Samples that are diluted can have higher errors than indicated in Section 15 than non-diluted samples.

1.4Volatile samples (such as high vapor pressure gasolines or light hydrocarbons) may not meet the stated precision because of selective loss of light materials during the analysis.

1.5A fundamental assumption in this test method is that the standard and sample matrices are well matched, or that the matrix differences are accounted for (see 13.2). Matrix mismatch can be caused by C/H ratio differences between samples and standards or by the presence of other interfering heteroatoms or species (see Table 1).

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 7547 : 2023 Standard Specification for Hydrocarbon Unleaded Aviation Gasoline
ASTM D 6751 : 2024 Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels
ASTM D 2880 : 2023 Standard Specification for Gas Turbine Fuel Oils
ASTM D 6448 : 2016 : R2022 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 4814 : 2024 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 7484 : 2023 : REV A Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine
ASTM D 8235 : 2021 Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 3238 : 2022 : REV A Standard Test Method for Calculation of Carbon Distribution and Structural Group Analysis of Petroleum Oils by the n-d-M Method
ASTM D 7807 : 2020 Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection
ASTM D 8048 : 2024 Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine
ASTM D 8074 : 2023 Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine
ASTM D 8011 : 2019 Standard Specification for Natural Gasoline as a Blendstock in Ethanol Fuel Blends or as a Denaturant for Fuel Ethanol
ASTM D 7223 : 2021 Standard Specification for Aviation Certification Turbine Fuel
ASTM D 7422 : 2023 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5623 : 2024 Standard Test Method for Sulfur Compounds in Light Petroleum Liquids by Gas Chromatography and Sulfur Selective Detection
ASTM D 8275 : 2022 Standard Specification for Gasoline-like Test Fuel for Compression-Ignition Engines
ASTM D 7862 : 2021 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6750 : 2023 Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)
ASTM D 8056 : 2024 Standard Guide for Elemental Analysis of Crude Oil
ASTM D 8350 : 2024 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine
ASTM D 8256 : 2024 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
ASTM D 5967 : 2021 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 7455 : 2019 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 5983 : 2021 Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Blending With Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4868 : 2017 Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
ASTM D 1655 : 2024 Standard Specification for Aviation Turbine Fuels
ASTM D 7156 : 2024 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine
ASTM D 4806 : 2021 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6074 : 2015 : R2022 Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils
ASTM D 8147 : 2024 Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines
ASTM D 4529 : 2017 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 4057 : 2022 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 396 : 2024 Standard Specification for Fuel Oils
ASTM D 7826 : 2023 : REV B Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives
ASTM D 975 : 2024 Standard Specification for Diesel Fuel
ASTM D 5966 : 2022 Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine
ASTM D 240 : 2019 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
ASTM D 8434 : 2021 Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Organo-metallic Additive
ASTM D 4054 : 2023 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM D 3994 : 2022 Standard Performance Specification for Woven Swimwear Fabrics
ASTM D 6923 : 2023 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure
ASTM D 7960 : 2021 Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Non-hydrocarbon Components
ASTM D 8291 : 2024 Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine
ASTM D 6618 : 2023 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine
ASTM D 7468 : 2022 Standard Test Method for Cummins ISM Test
ASTM D 7549 : 2024 Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure
ASTM D 7343 : 2020 Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 6615 : 2022 Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel
ASTM D 7583 : 2016 : R2023 Standard Test Method for John Deere Coolant Cavitation Test
ASTM D 910 : 2024 Standard Specification for Leaded Aviation Gasolines
ASTM D 6823 : 2008 : R2021 Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils
ASTM D 3699 : 2019 Standard Specification for Kerosine
ASTM D 6227 : 2024 Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component
ASTM D 7666 : 2012 : R2019 Standard Specification for Triglyceride Burner Fuel
ASTM D 6681 : 2023 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure
ASTM D 7719 : 2021 : REV A Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline Test Fuel
ASTM D 7578 : 2020 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 4809 : 2018 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)
ASTM D 7467 : 2023 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
ASTM D 4485 : 2022 : EDT 1 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 8076 : 2021 : REV B Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines
ASTM D 3338/D3338M : 2020 : REV A Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 7566 : 2024 : REV A Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 8252 : 2023 Standard Test Method for Vanadium and Nickel in Crude and Residual Oil by X-ray Spectrometry
ASTM D 4529 : 2024 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 1655 : 2024 : REV B Standard Specification for Aviation Turbine Fuels
ASTM D 6823 : 2024 Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils
ASTM D 8291 : 2024 : REV A Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine
ASTM D 6448 : 2024 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 8256 : 2024 : REV A Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
ASTM D 4054 : 2024 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM D 7455 : 2024 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 3699 : 2024 Standard Specification for Kerosine
ASTM D 7826 : 2024 Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives
ASTM D 4485 : 2024 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 8076 : 2024 Standard Specification for 95, 98, and 100 Research Octane Number Test Fuels for Automotive Spark-Ignition Engines
ASTM D 6227 : 2024 : REV A Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component
ASTM D 8350 : 2024 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine
ASTM D 975 : 2024 : REV A Standard Specification for Diesel Fuel
ASTM D 7566 : 2024 : REV D Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons

ASTM D 4175 : 2024 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2024 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.