ASTM D 2684/D2684M : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Permeability of Thermoplastic Containers to Packaged Reagents or Proprietary Products (Withdrawn 2024)
Hardcopy , PDF
01-07-2024
English
01-09-2015
Committee |
D 20
|
DocumentType |
Test Method
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers procedures for determining the permeability of thermoplastic containers to packaged reagents or proprietary products under specified conditions of exposure. The exposures used are intended to simulate the normal and elevated temperature-storage conditions that might be encountered in end-use application.
1.2This test method is applicable only to those types of containers designed to allow positive, leakproof closure.
1.3Two procedures are provided:
1.3.1Procedure Ais specific to testing only with a standard design container. This procedure provides for determinations of rate of weight loss (or gain) and for calculation of a permeability factor.
1.3.2Procedure Bapplies to tests of all other container designs. Permeability data by this procedure are expressed only in terms of rate of weight loss (or gain) for the particular container tested.
1.4Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1:There is no known ISO equivalent to this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 4976 : 2006 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 4976 : 2000 : REV B | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 4976 : 2004 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 4976 : 2004 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 1505 : 2003 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 4976 : 2012 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 4976 : 2012 : REV A : R2020 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 4976 : 2002 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 1505 : 1968 : R1979 | Standard Test Method for Density Of Plastics By The Density-Gradient Technique |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 1505 : 2010 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 1505 : 2018 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 4976 : 2002 : EDT 1 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 1505 : 1998 : EDT 1 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.