![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 2892 : 2018 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column)
Hardcopy , PDF
28-04-2020
English
01-12-2018
This test method covers the procedure for the distillation of stabilized crude petroleum (seeNote 1) to a final cut temperature of 400 °C Atmospheric Equivalent Temperature (AET).
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
34
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the procedure for the distillation of stabilized crude petroleum (see Note 1) to a final cut temperature of 400 °C Atmospheric Equivalent Temperature (AET). This test method employs a fractionating column having an efficiency of 14 to 18 theoretical plates operated at a reflux ratio of 5:1. Performance criteria for the necessary equipment is specified. Some typical examples of acceptable apparatus are presented in schematic form. This test method offers a compromise between efficiency and time in order to facilitate the comparison of distillation data between laboratories.
Note 1:Defined as having a Reid vapor pressure less than 82.7 kPa (12 psi).
1.2This test method details procedures for the production of a liquefied gas, distillate fractions, and residuum of standardized quality on which analytical data can be obtained, and the determination of yields of the above fractions by both mass and volume. From the preceding information, a graph of temperature versus mass % distilled can be produced. This distillation curve corresponds to a laboratory technique, which is defined at 15/5 (15 theoretical plate column, 5:1 reflux ratio) or TBP (true boiling point).
1.3This test method can also be applied to any petroleum mixture except liquefied petroleum gases, very light naphthas, and fractions having initial boiling points above 400 °C.
1.4This test method contains the following annexes and appendixes:
1.4.1Annex A1—Test Method for the Determination of the Efficiency of a Distillation Column,
1.4.2Annex A2—Test Method for the Determination of the Dynamic Holdup of a Distillation Column,
1.4.3Annex A3—Test Method for the Determination of the Heat Loss in a Distillation Column (Static Conditions),
1.4.4Annex A4—Test Method for the Verification of Temperature Sensor Location,
1.4.5Annex A5—Test Method for Determination of the Temperature Response Time,
1.4.6Annex A6—Practice for the Calibration of Sensors,
1.4.7Annex A7—Test Method for the Verification of Reflux Dividing Valves,
1.4.8Annex A8—Practice for Conversion of Observed Vapor Temperature to Atmospheric Equivalent Temperature (AET),
1.4.9Appendix X1—Test Method for Dehydration of a Sample of Wet Crude Oil, and
1.4.10Appendix X2—Practice for Performance Check.
1.5The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.6WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 10.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 5191 : 2019 | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 7398 : 2011 : R2016 | Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 °C to 615 °C by Gas Chromatography |
ASTM D 1655 : 2019 | Standard Specification for Aviation Turbine Fuels |
ASTM D 7807 : 2012 | Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection |
ASTM D 5399 : 2009 : R2017 | Standard Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography |
ASTM D 6378 : 2018 : REV A | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 6352 : 2015 | Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography |
ASTM D 7566 : 2019 | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
ASTM D 6377 : 2016 | Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCR<inf>x</inf > (Expansion Method) |
ASTM D 5188 : 2016 | Standard Test Method for Vapor-Liquid Ratio Temperature Determination of Fuels (Evacuated Chamber and Piston Based Method) |
ASTM D 6897 : 2016 | Standard Test Method for Vapor Pressure of Liquefied Petroleum Gases (LPG) (Expansion Method) |
ASTM D 7169 : 2018 | Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography |
ASTM D 7798 : 2015 | Standard Test Method for Boiling Range Distribution of Petroleum Distillates with Final Boiling Points up to 538 °C by Ultra Fast Gas Chromatography (UF GC) |
ASTM D 2887 : 2019 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 7213 : 2015 | Standard Test Method for Boiling Range Distribution of Petroleum Distillates in the Boiling Range from 100 °C to 615 °C by Gas Chromatography |
ASTM D 6729 : 2014 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100 Metre Capillary High Resolution Gas Chromatography |
ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 6300 : 2013 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6729 : 2001 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100 Meter Capillary High Resolution Gas Chromatography |
ASTM D 6300 : 2014 : REV A : EDT 1 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1298 : 2012 : REV A | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 6733 : 2001 : R2016 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Metre Capillary High Resolution Gas Chromatography |
ASTM D 5134 : 1998 : R2003 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through <i>n</i>-Nonane by Capillary Gas Chromatography |
ASTM D 4006 : 1981 : R2000 : EDT 1 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 1217 : 2015 | Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer |
ASTM D 6300 : 2017 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1298 : 2012 : REV B | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 1217 : 1993 : R1998 | Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer |
ASTM D 6730 : 2001 : R2006 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100-Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 5134 : 2013 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography |
ASTM D 6300 : 2017 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 2887 : 2006 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 4006 : 2016 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 6300 : 2016 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 4006 : 2016 : EDT 1 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 1298 : 1999 : R2005 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 6730 : 2001 : R2006 : EDT 1 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 6300 : 2004 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1298 : 2012 : REV B : R2017 | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 1298 : 2012 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 6730 : 2019 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100-Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 6730 : 2001 : R2016 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 1298 : 1999 : EDT 2 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 4006 : 2011 : R2012 : EDT 1 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 6300 : 2019 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2887 : 1999 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 6729 : 2004 : EDT 1 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100 Metre Capillary High Resolution Gas Chromatography |
ASTM D 2887 : 2006 : REV A | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 2887 : 2014 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 6729 : 2004 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100 Meter Capillary High Resolution Gas Chromatography |
ASTM D 2887 : 2001 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 1298 : 1999 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 6730 : 2001 : R2011 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 4006 : 2007 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 1217 : 1993 : R2007 | Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer |
ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 6300 : 2006 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2014 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2887 : 2001 : REV A | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 6300 : 2015 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1298 : 1999 : EDT 1 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 6300 : 1999 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2887 : 2016 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 2887 : 2008 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 2887 : 2019 : EDT 1 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 2887 : 2018 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 2887 : 2012 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
ASTM D 6300 : 2013 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6733 : 2001 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Meter Capillary High Resolution Gas Chromatography |
ASTM D 6729 : 2004 : R2009 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100 Metre Capillary High Resolution Gas Chromatography |
ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 4006 : 2011 : R2012 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 4006 : 1981 : R2005 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 6300 : 2008 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2003 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1217 : 2012 | Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer |
ASTM D 6733 : 2001 : R2006 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Metre Capillary High Resolution Gas Chromatography |
ASTM D 6300 : 2007 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 4006 : 2011 | Standard Test Method for Water in Crude Oil by Distillation |
ASTM D 2887 : 2013 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 2887 : 2015 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 5134 : 1998 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography |
ASTM D 2887 : 2015 : EDT 1 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 3710 : 1995 : R1999 : EDT 1 | Standard Test Method for Boiling Range Distribution of Gasoline and Gasoline Fractions by Gas Chromatography |
ASTM D 2887 : 2004 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 6300 : 2002 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 5134 : 1998 : R2008 : EDT 1 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography |
ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 6733 : 2001 : R2011 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Metre Capillary High Resolution Gas Chromatography |
ASTM D 2887 : 2002 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 1298 : 1985 : R1990 : EDT 1 | Standard Practice for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 6300 : 2016 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 5134 : 2013 : R2017 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography |
ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 2887 : 2016 : REV A | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 2887 : 2004 : REV A | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 6300 : 2014 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 1217 : 1993 : R2003 : EDT 1 | Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer |
ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 2887 : 2003 | Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography |
ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6730 : 2001 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100-Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.