ASTM D 3165 : 2007 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies
Hardcopy , PDF
13-01-2023
English
21-03-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 15.06, 2015 Defines test method which is intended for Determining the comparative shear strengths of adhesives in large area joints when tested on a standard single-lap-joint specimen and under specified conditions of preparation and testing.
| Committee |
D 14
|
| DocumentType |
Test Method
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method (Note 1) is intended for determining the comparative shear strengths of adhesives in large area joints when tested on a standard single-lap-joint specimen and under specified conditions of preparation and testing. Adhesives respond differently in small versus large area joints (Note 2).
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 1556 : 2020 | Standard Specification for Epoxy Resin System for Composite Skin, Honeycomb Sandwich Panel Repair |
| ASTM E 1556 : 2012 | Standard Specification for Epoxy Resin System for Composite Skin, Honeycomb Sandwich Panel Repair |
| ASTM D 5573 : 1999 : R2019 | Standard Practice for Classifying Failure Modes in Fiber-Reinforced-Plastic (FRP) Joints |
| ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| ASTM D 4896 : 2001 : R2016 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 2919 : 2001 : R2014 | Standard Test Method for Determining Durability of Adhesive Joints Stressed in Shear by Tension Loading |
| ASTM D 2651 : 1990 : R1995 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
| ASTM D 2093 : 2003 : R2017 | Standard Practice for Preparation of Surfaces of Plastics Prior to Adhesive Bonding |
| ASTM D 3933 : 1998 : R2004 | Standard Guide for Preparation of Aluminum Surfaces for Structural Adhesives Bonding (Phosphoric Acid Anodizing) |
| ASTM B 265 : 2015 : REDLINE | Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate |
| ASTM B 209 : 2014 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM D 4896 : 2001 : R2008 : EDT 1 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 4896 : 1995 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 4896 : 2001 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 3933 : 1998 | Standard Guide for Preparation of Aluminum Surfaces for Structural Adhesives Bonding (Phosphoric Acid Anodizing) |
| ASTM A 366/A366M : 1997 | SPECIFICATION FOR COMMERCIAL STEEL (CS) SHEET, CARBON, (0.15 MAXIMUM PERCENT) COLD-ROLLED |
| ASTM D 3933 : 1998 : R2010 | Standard Guide for Preparation of Aluminum Surfaces for Structural Adhesives Bonding (Phosphoric Acid Anodizing) |
| ASTM D 2651 : 2001 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
| ASTM B 152/B152M : 2013 : REDLINE | Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar |
| ASTM B 265 : 2005 : EDT 1 | Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate |
| ASTM D 2093 : 2003 : R2011 | Standard Practice for Preparation of Surfaces of Plastics Prior to Adhesive Bonding |
| ASTM D 907 : 2015 : REDLINE | Standard Terminology of Adhesives |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM D 2093 : 1997 | Standard Practice for Preparation of Surfaces of Plastics Prior to Adhesive Bonding |
| ASTM D 2093 : 2003 | Standard Practice for Preparation of Surfaces of Plastics Prior to Adhesive Bonding |
| ASTM D 4896 : 2001 : R2016 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 2651 : 2001 : R2016 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
| ASTM D 2651 : 2001 : R2008 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
| ASTM D 3933 : 1998 : R2017 | Standard Guide for Preparation of Aluminum Surfaces for Structural Adhesives Bonding (Phosphoric Acid Anodizing) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.