ASTM D 3165 : 2007 : R2023
Current
The latest, up-to-date edition.
Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies
Hardcopy , PDF
English
10-01-2023
Committee |
D 14
|
DocumentType |
Test Method
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method (Note 1) is intended for determining the comparative shear strengths of adhesives in large area joints when tested on a standard single-lap-joint specimen and under specified conditions of preparation and testing. Adhesives respond differently in small versus large area joints (Note 2).
Note 1:While this test method is intended for use in metal-to-metal applications, it may be used for measuring the shear properties of adhesives using plastic adherends, provided consideration is given to the thickness and rigidity of the plastic adherends. Doublers or bonded tabs may be required for plastic adherends to prevent bearing failure in the adherends.
Note 2:This variation can be influenced by adhesive density, flow characteristics, cure rate, gel time, carrier composition, entrapped volatiles, volatiles released during cure, etc. and also by cure cycle variables including: temperature, time, pressure, rise rate to temperature, cool-down rate, etc. In addition to the processing variables joint size changes the level of constraint on the adhesive as well as the influence of induced tensile loads at the edge of the joint during mechanical or thermal loading.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E 1556 : 2020 | Standard Specification for Epoxy Resin System for Composite Skin, Honeycomb Sandwich Panel Repair |
ASTM D 4896 : 2001 : R2016 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
ASTM D 5573 : 1999 : R2019 | Standard Practice for Classifying Failure Modes in Fiber-Reinforced-Plastic (FRP) Joints |
ASTM B 36/B36M : 2018 | Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar |
ASTM D 4896 : 2001 : R2024 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
ASTM D 907 : 2015 | Standard Terminology of Adhesives |
ASTM B 152/B152M : 2024 | Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar |
ASTM B 36/B36M : 2023 | Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar |
ASTM D 907 : 2015 : R2023 | Standard Terminology of Adhesives |
ASTM B 152/B152M : 2019 | Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar |
ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
ASTM D 2651 : 2001 : R2024 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
ASTM D 2651 : 2001 : R2016 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
ASTM E 4 : 2024 | Standard Practices for Force Calibration and Verification of Testing Machines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.