Skip to content
Please enter a keyword to search

  • ASTM D 3567 : 2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings

    Available format(s):  Hardcopy, PDF

    Superseded date:  18-06-2022

    Language(s):  English

    Published date:  12-10-2017

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This practice covers the determination of outside diameter, inside diameter, total wall thickness, reinforced wall thickness, liner thickness (where applicable), and length dimensions of “fiberglass” (glass-fiber-reinforced thermosetting resin) pipe. Included are procedures for measuring tapered dimensions and taper angles for pipe intended to be joined by tapered socket fittings, and procedures for gaging internal and external threads.

    1.2This practice also includes procedures for determining dimensions for fiberglass pipe fittings.

    1.3The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.

    Note 1:There is no known ISO equivalent to this standard.

    1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee D 20
    Document Type Standard Practice
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM D 5365 : 2018 Standard Test Method for Long-Term Ring-Bending Strain of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
    ASTM D 5685 : 2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings
    ASTM D 2143 : 2015 Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
    ASTM D 3517 : 2014 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe
    ASTM D 3262 : 2016 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe
    ASTM D 2997 : 2015 Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
    ASTM F 1743 : 2017 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
    ASTM D 2517 : 2018 Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
    ASTM D 2925 : 2014 Standard Test Method for Beam Deflection of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe Under Full Bore Flow
    ASTM F 2019 : 2011 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
    ASTM F 1417 : 2011 : REV A : R2015 Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air
    ASTM D 3754 : 2014 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
    ASTM F 1173 : 2001 : R2018 Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications
    ASTM D 2105 : 2001 : R2014 Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
    ASTM F 1417 : 2011 : REV A : R2019 Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air
    ASTM D 2105 : 2001 : R2019 Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
    ASTM D 3517 : 2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe
    ASTM D 3754 : 2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
    ASTM D 2925 : 2014(R2019) Standard Test Method for Beam Deflection of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe Under Full Bore Flow
    ASTM D 3840 : 2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications
    ASTM D 2997 : 2021 Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
    ASTM D 1598 : 2021 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
    ASTM D 5813 : 2004 : R2018 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
    ASTM D 2992 : 2018 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
    ASTM F 1743 : 2021 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
    ASTM D 2143 : 2021 Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
    ASTM F 1216 : 2021 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
    ASTM F 1417 : 2011 : REV A : R2019 : EDT 1 Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air
    ASTM F 2019 : 2020 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
    ASTM D 3262 : 2020 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe
    ASTM D 6041 : 2018 Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
    ASTM D 3681 : 2018 Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
    ASTM D 1599 : 2018 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
    ASTM F 1216 : 2016 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
    ASTM D 6783 : 2005 : REV A : R2017 Standard Specification for Polymer Concrete Pipe
    ASTM D 5677 : 2017 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines
    ASTM D 2996 : 2017 Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
    ASTM D 3840 : 2014 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 4166 : 1999 : R2004 : EDT 1 Standard Test Method for Measurement of Thickness of Nonmagnetic Materials by Means of a Digital Magnetic Intensity Instrument (Withdrwan 2008)
    ASTM D 4166 : 1999 Standard Test Method for Measurement of Thickness of Nonmagnetic Materials by Means of a Digital Magnetic Intensity Instrument
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective