ASTM D 3641 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
29-05-2021
English
30-06-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.02, 2015 Defines the general principles to be followed when injection molding test specimens of thermoplastic molding and extrusion materials.
| Committee |
D 20
|
| DevelopmentNote |
Supersedes ASTM D 647. (02/2002)
|
| DocumentType |
Redline
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This practice covers the general principles to be followed when injection molding test specimens of thermoplastic molding and extrusion materials. This practice is to be used to obtain uniformity in methods of describing the various steps of the injection molding process and to set up uniform methods of reporting these conditions. The exact conditions required to prepare suitable specimens will vary for each plastic material. Any requirements or recommendations in the material specification that differ from this standard take precedence over those in this standard. Always consult the referenced material document for specimen preparation. If no referenced document exists, then consult the material supplier for specimen preparation guidance and note such in the test report.
1.2The methodology presented assumes the use of reciprocating screw injection molding machines.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:This practice is equivalent to the following parts of ISO 294: Plastics—Injection Moulding of Test Specimens of Thermoplastic Materials; 294-1: Part 1—General Principles and Multipurpose Test Specimens (ISO Type A Mould) and Bars (ISO Type B Mould); ISO 294-2: Part 2—Small Tensile Bars (ISO Type C Mould); ISO 294-3: Part 3—Plates (ISO Type D Moulds).
| ASTM D 6835 : 2017 : REDLINE | Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE) |
| ASTM D 4673 : 2016 : REDLINE | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
| ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ASTM D 5939 : 1996 | Standard Test Method for Injection Moulding of Test Specimens of Thermoplatic Materials (Withdrawn 1998) |
| ASTM D 788 : 2016 : REDLINE | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
| SAE J2749_201707 | High Strain Rate Tensile Testing of Polymers |
| ASTM D 955 : 2008 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
| (INACTIVE RECORD)ASTM D 5336 : 2015-04 | CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPHTHALAMIDE (PPA) INJECTION MOLDING MATERIALS |
| ASTM D 4067 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
| ASTM D 5204 : 2017 : REDLINE | CLASSIFICATION SYSTEM FOR POLYAMIDE-IMIDE (PAI) MOLDING AND EXTRUSION MATERIALS |
| ASTM D 5676 : 1999 | Standard Specification for Recycled Polystyrene Molding and Extrusion Materials (Withdrawn 2004) |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 3965 : 2016 : REDLINE | Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings |
| ASTM D 6394 : 2014 : REDLINE | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 787 : 2012-08 | SPECIFICATION FOR ETHYL CELLULOSE MOLDING AND EXTRUSION COMPOUNDS |
| ASTM D 4634 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
| ASTM F 2617 : 2015 : REDLINE | Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry |
| ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ASTM D 5593 : 1999 : EDT 1 | Standard Classification for Thermoplastic Elastomers-Olefinic (TEO) (Withdrawn 2005) |
| ASTM D 4203 : 2017 : REDLINE | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
| ASTM D 6339 : 2011 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
| ASTM D 5205 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ASTM D 1562 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM D 707 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ASTM D 5021 : 2000 | Standard Specification for Thermoplastic Elastomer-Chlorinated Ethylene Alloy (TECEA) (Withdrawn 2007) |
| ASTM D 5138 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM D 955 : 2008 : R2014 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
| ASTM D 706 : 2015 : REDLINE | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM D 5990 : 2000 | Standard Classification System for Polyketone Injection Molding and Extrusion Materials (PK) (Withdrawn 2007) |
| ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
| ASTM D 957 : 2012 : REDLINE | Standard Practice for Determining Surface Temperature of Molds for Plastics |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ASTM D 1525 : 2017 | Standard Test Method for Vicat Softening Temperature of Plastics |
| ISO 294-2:1996 | Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 648 : 2016 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 20753:2008 | Plastics Test specimens |
| ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.