• There are no items in your cart

ASTM D 5592 : 1994

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Material Properties Needed in Engineering Design Using Plastics

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

01-01-1994

CONTAINED IN VOL. 08.03, 2018 Describes the essential material properties needed for designing with plastics. Its purpose is to raise the awareness of the plastics community regarding the specific considerations involved in using the appropriate material properties in design calculations.

1.1 This guide covers the essential material properties needed for designing with plastics. Its purpose is to raise the awareness of the plastics community regarding the specific considerations involved in using the appropriate material properties in design calculations.

1.2 This guide is intended only as a convenient resource for engineering design. It should be noted that the specific operating conditions (temperature, applied stress or strain, environment, etc. and corresponding duration of such exposures) could vary significantly from one application to another. It is, therefore, the responsibility of the user to perform any pertinent tests under actual conditions of use to determine the suitability of the material in the intended application.

1.3 The applicable ISO and ASTM standard methods for the relevant material properties are listed in this guide for the benefit of design engineers.

1.4 It should be noted that for some of the desired properties, no ASTM or ISO standards exist. These include pvT data, no-flow temperature, ejection temperature, and fatigue in tension. In these instances, relying on available test methods is suggested.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1-There is no similar or equivalent ISO standard.

Committee
D 20
DocumentType
Guide
Pages
6
ProductNote
Reconfirmed 1994
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ISO 2578:1993 Plastics Determination of time-temperature limits after prolonged exposure to heat
ASTM D 3418 : 2015 : REDLINE Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 671 : 1993 Standard Test Method for Flexural Fatigue of Plastics by Constant-Amplitude-of-Force (Withdrawn 2002)
ASTM D 1894 : 2014 : REDLINE Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM E 228 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
ISO 6721-2:2008 Plastics Determination of dynamic mechanical properties Part 2: Torsion-pendulum method
ISO 3167:2014 Plastics Multipurpose test specimens
ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ASTM D 3045 : 1992 PRACTICE FOR HEAT AGING OF PLASTICS WITHOUT LOAD
ASTM D 5279 : 2013 : REDLINE Standard Test Method for Plastics: Dynamic Mechanical Properties: In Torsion
ISO 11443:2014 Plastics Determination of the fluidity of plastics using capillary and slit-die rheometers
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 5045 : 2014 : REDLINE Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials
ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ASTM D 3641 : 2015 : REDLINE Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 2991 : 1984 Recommended Practice for Testing Stress-Relaxation of Plastics (Withdrawn 1990)
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11403-2:2012 Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties
ASTM D 1435 : 2013 : REDLINE Standard Practice for Outdoor Weathering of Plastics
ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
ISO 604:2002 Plastics — Determination of compressive properties
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ASTM D 3835 : 2016 : REDLINE Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ASTM D 2565 : 2016 : REDLINE Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 11403-1:2014 Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties
ISO 8295:1995 Plastics Film and sheeting Determination of the coefficients of friction
ASTM D 695 : 2015 : REDLINE Standard Test Method for Compressive Properties of Rigid Plastics
ISO 4607:1978 Plastics Methods of exposure to natural weathering
ASTM D 2990 : 2017 : REDLINE Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles

View more information
€69.98
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.