• Shopping Cart
    There are no items in your cart

ASTM D 4703 : 2007

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Superseded by

ASTM D 4703 : 2010

Language(s)

English

Published date

01-04-2007

€74.48
Excluding VAT

Committee
D 20
DocumentType
Standard Practice
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1 This practice covers the compression molding of thermoplastic granules and milled stock for the preparation of test specimens.

1.2 While conditions for certain materials are given, the primary source of specific conditions shall be the material specification standards for each type of material.

1.3 The values stated in SI units are to be regarded as the standard. The values given in brackets are for information only.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1

The main body of this practice is equivalent to ISO 293-1986. and ISO 293-1986 differ in some details; however, specimens prepared using , Procedure A should be equivalent to those prepared using ISO 293-1986, Cooling Method D. Specimens prepared using , Procedure C should be equivalent to those prepared using ISO 293-1986, Cooling Method B. However, due to the greater cooling rate tolerances of the ISO standard, specimens prepared in accordance with ISO Cooling Method B may not be equivalent to , Procedure C.

ASTM F 2136 : 2018 Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
ASTM D 3350 : 2014 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 5885/D5885M : 2017 Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry
ASTM D 8117 : 2017 Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by Differential Scanning Calorimetry
ASTM D 1505 : 2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 2839 : 2016 Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
ASTM D 955 : 2008 : R2014 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
ASTM D 1784 : 2011 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
ASTM D 3981 : 2009 : REV A : R2016 Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications
ASTM D 6247 : 2018 Standard Test Method for Determination of Elemental Content of Polyolefins by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM F 3181 : 2016 Standard Test Method for The Un-notched, Constant Ligament Stress Crack Test (UCLS) for HDPE Materials Containing Post- Consumer Recycled HDPE
ASTM D 7436 : 2017 Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology
ASTM D 4020 : 2018 Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials
ASTM D 1693 : 2015 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 4635 : 2016 Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications
ASTM D 4883 : 2018 Standard Test Method for Density of Polyethylene by the Ultrasound Technique
ASTM D 5575 : 2018 Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
ASTM D 2103 : 2015 Standard Specification for Polyethylene Film and Sheeting
ASTM F 2947/F2947M : 2019 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM D 3895 : 2019 Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
ASTM F 2922 : 2013 : R2018 Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers
ASTM D 4976 : 2012 : REV A Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 883 : 2019 : REV B Standard Terminology Relating to Plastics
ASTM F 2617 : 2015 Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry
ASTM D 1248 : 2016 Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
ASTM D 3004 : 2008 : R2013 Standard Specification for Crosslinked and Thermoplastic Extruded Semi-Conducting, Conductor and Insulation Shielding Materials
ASTM D 1998 : 2015 Standard Specification for Polyethylene Upright Storage Tanks
ASTM D 5397 : 2019 Standard Test Method for Evaluation of Stress Crack Resistance of Polyolefin Geomembranes Using Notched Constant Tensile Load Test
ASTM F 1473 : 2018 Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.