ASTM D 5147/D5147M : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material
Hardcopy , PDF
12-11-2024
English
01-07-2018
1.1These test methods cover procedures for sampling and testing prefabricated, reinforced, polymer-modified bituminous sheet materials designed for single- or multiple-ply application in roofing and waterproofing membranes. These products may use various surfacing materials on one side.1.2These test methods cover a number of different products. Not all tests are required for every product. Only those called out in the Product Standard are required.1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Committee |
D 08
|
DocumentType |
Test Method
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1These test methods cover procedures for sampling and testing prefabricated, reinforced, polymer-modified bituminous sheet materials designed for single- or multiple-ply application in roofing and waterproofing membranes. These products may use various surfacing materials on one side.
1.2These test methods cover a number of different products. Not all tests are required for every product. Only those called out in the Product Standard are required.
1.3These test methods appear in the following order:
Section | |
Sampling | 4 |
Conditioning | 5 |
Thickness | 6 |
Load Strain Properties | 7 |
Tear Strength | 8 |
Moisture Content | 9 |
Water Absorption | 10 |
Dimensional Stability | 11 |
Low-Temperature Flexibility | 12 |
Heat Conditioning | 13 |
Accelerated Weathering | 14 |
Granule Embedment | 15 |
Compound Stability | 16 |
Coating Thickness | 17 |
Low Temperature Unrolling | 18 |
Precision and Bias | 19 |
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7694/D7694M : 2018 | Standard Test Methods for Self-Adhesive Modified Bituminous Sheet Material |
ASTM D 3105 : 2017 : R2024 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
ASTM D 2643/D2643M : 2021 | Standard Specification for Prefabricated Bituminous Geomembrane Used as Canal and Ditch Liner (Exposed Type) |
ASTM D 5849/D5849M : 2021 | Standard Test Method for Evaluating Resistance of Modified Bituminous Roofing Membrane to Cyclic Fatigue (Joint Displacement) |
ASTM D 7505/D7505M : 2017 : R2023 | Standard Specification for Self-Adhesive Polyester Fabric Reinforced Polymer-Modified Asphalt Steep Slope Roll Roofing Surfaced with Mineral Granules |
ASTM D 7832/D7832M : 2024 | Standard Guide for Performance Attributes of Waterproofing Membranes Applied to Below-Grade Walls / Vertical Surfaces (Enclosing Interior Spaces) |
ASTM E 1993/E1993M : 1998 : R2020 | Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs |
ASTM D 7051 : 2005 : R2020 | Standard Test Method for Cyclic Thermal Shock of SBS-Modified Bituminous Roofing Sheets with Factory-Applied Metal Surface |
ASTM D 7379/D7379M : 2008 : R2021 | Standard Test Methods for Strength of Modified Bitumen Sheet Material Laps Using Cold Process Adhesive |
ASTM D 1970/D1970M : 2021 | Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection |
ASTM D 6630/D6630M : 2016 : R2022 | Standard Guide for Low-Slope Insulated Roof Membrane Assembly Performance |
ASTM D 6455 : 2011 : R2018 | Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs) |
ASTM D 7530/D7530M : 2017 : R2023 | Standard Specification for Self-Adhesive Glass Fiber Fabric Reinforced Polymer-Modified Asphalt Steep Slope Roll Roofing Surfaced with Mineral Granules |
ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM D 1204 : 2007 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM D 95 : 2023 : EDT 1 | Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation |
ASTM D 6298/D6298M : 2016 : R2023 | Standard Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface |
ASTM D 6222/D6222M : 2016 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 6298/D6298M : 2016 | Standard Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface |
ASTM D 1204 : 2014 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM D 5869/D5869M : 2007 : REV A : R2018 : EDT 1 | Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials |
ASTM D 6509/D6509M : 2016 : R2023 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Base Sheet Materials Using Glass Fiber Reinforcements |
ASTM D 4073 : 2006 : R2013 | Standard Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 5636/D5636M : 1994 : R2017 | Standard Test Method for Low Temperature Unrolling of Felt or Sheet Roofing and Waterproofing Materials |
ASTM D 1204 : 2008 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM D 1204 : 2014 : R2020 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 95 : 2013 : R2018 | Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation |
ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 6162/D6162M : 2016 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 4073 : 1994 : R1998 : EDT 1 | Standard Test Method for Tensile-Tear Strength of Bituminuous Roofing Membranes |
ASTM D 4073 : 1994 : R2003 | Standard Test Method for Tensile-Tear Strength of Bituminuous Roofing Membranes |
ASTM D 5636/D5636M : 1994 : R2022 | Standard Test Method for Low-Temperature Unrolling of Felt or Sheet Roofing and Waterproofing Materials |
ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 6222/D6222M : 2016 : R2023 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements |
ASTM D 6163/D6163M : 2021 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements |
ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 6223/D6223M : 2021 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 1204 : 1994 : EDT 1 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM D 5869/D5869M : 2007 : REV A : R2023 | Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials |
ASTM D 4073 : 2006 | Standard Test Method for Tensile-Tear Strength of Bituminuous Roofing Membranes |
ASTM D 6509/D6509M : 2016 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Base Sheet Materials Using Glass Fiber Reinforcements |
ASTM D 1204 : 2002 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM D 6162/D6162M : 2021 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 6223/D6223M : 2016 | Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements |
ASTM D 95 : 2023 | Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation |
ASTM D 6163/D6163M : 2016 | Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.