ASTM D 5204 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Classification System and Basis for Specification for Polyamide-Imide (PAI) Molding and Extrusion Materials
Hardcopy , PDF
21-11-2022
English
08-08-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.1.1This classification system covers polyamide-imide materials suitable for injection molding and extrusion.
| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This classification system covers polyamide-imide materials suitable for injection molding and extrusion.
1.2The properties included in this classification system are those required to identify the compositions covered. It is possible that other requirements are necessary to identify particular characteristics important to specialized applications. The use of suffixes as shown in Section 5 is one way of specifying these requirements.
1.3This standard allows for the use of recycled materials provided that specification requirements based upon this classification system are met.
1.4This classification system and subsequent line call-out (specification) is intended to be a means of calling out plastics materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection needs to be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than those covered by this classification, and the economics.
1.5The values stated in SI units are to be regarded as the standard. (Reporting in inch-pound units is acceptable.)
1.6The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 1508 : 1996 : R2021 | Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7292 : 2018 | Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI) |
| ASTM F 1508 : 1996 : R2016 : EDT 1 | Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 150 : 2022 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM D 1708 : 2002 | Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens |
| ASTM D 257 : 2014 | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM D 3641 : 2021 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3641 : 2015 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 150 : 2018 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM D 257 : 2014 : R2021 : EDT 1 | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.