ASTM D 5207 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials
Hardcopy , PDF
14-12-2020
English
05-06-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 20
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers the confirmation of test flames for small-scale burning tests on plastic materials using the laboratory burner described in Specification D5025. Back pressures and flow rates for methane, propane, and butane supply gases are given for specific test flames. This practice describes a procedure to confirm the heat evolution of the test flame.
1.2The values stated in SI units are to be regarded as the standard.
1.3This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.4Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 1505 : 2016 | Standard Specification for Insulated and Insulating Hand Tools |
| ASTM D 4804 : 2019 | Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics |
| ASTM D 2633 : 2013 : REV A | Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable |
| ASTM D 5025 : 2012 : EDT 1 | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 3801 : 2019 | Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position |
| ASTM E 3020 : 2016 : REV A | Standard Practice for Ignition Sources |
| ASTM D 470 : 2013 | Standard Test Methods for Crosslinked Insulations and Jackets for Wire and Cable |
| ASTM D 635 : 2018 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
| ASTM D 3195 : 1990 : R2004 | Standard Practice for Rotameter Calibration |
| ASTM D 5025 : 2012 | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 5025 : 2005 | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 5025 : 2020 : REV A | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 5025 : 2012 : EDT 1 | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 5025 : 2020 | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 5025 : 1999 | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 5025 : 2011 | Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials |
| ASTM D 3195 : 1990 : R1998 : EDT 1 | Standard Practice for Rotameter Calibration |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.