ASTM D 5286 : 2020
Current
The latest, up-to-date edition.
Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints
Hardcopy , PDF
English
01-06-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover the determination of the transfer efficiency of spray-applied coatings under general plant conditions. Transfer efficiency is the ratio of paint solids deposited to the total paint solids used during the application process, expressed as a percent.
1.2The transfer efficiency is calculated from the weight or volume of the paint solids sprayed and that of the paint solids deposited on the painted part.
1.3Limitations include the ability to accurately determine the amount of paint solids deposited on the part and the capability of accurate measurement of the amount of paint sprayed.
1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
Note 1:These test methods apply to general plant production equipment and procedures. A method specific to automotive plants is defined in Test Method D5066.
Note 2:The relationship between volatile organic compound emission rates and transfer efficiency in automobile and light duty truck topcoat operations, EPA 450/3-88-01, referenced in Test Method D5066 does not apply to general production facilities.
Note 3:A single-point transfer efficiency measurement may not represent the entire process.
Note 4:The operator and the spray-application equipment-operating conditions during the transfer efficiency measurement should be representative of normal operating conditions.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements see Section 7, and 10.3.1.
Note 5:These test methods have not been adopted by federal regulatory agencies for demonstration of compliance with air pollution regulations such as VOC, HAPS, etc.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 2697 : 2022 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D 5066 : 1991 : R2017 | Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints—Weight Basis |
| ASTM D 5066 : 1991 : R2023 | Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints—Weight Basis |
| ASTM D 1200 : 2023 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 1200 : 2010 : R2018 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 1186 : 1993 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base |
| ASTM D 2697 : 2003 : R2014 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D 1400 : 1994 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base |
| ASTM D 2697 : 2003 : R2021 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D 2369 : 2020 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 2369 : 2024 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 3925 : 2002 : R2022 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 3925 : 2002 : R2015 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.