ASTM D 5448/D5448M : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders
Hardcopy , PDF
17-06-2022
English
25-07-2016
This test method determines the inplane shear properties of wound polymer matrix composites reinforced by high-modulus continuous fibers.
Committee |
D 30
|
DocumentType |
Test Method
|
Pages |
13
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method determines the inplane shear properties of wound polymer matrix composites reinforced by high-modulus continuous fibers. It describes testing of hoop wound (90°) cylinders in torsion for determination of inplane shear properties.
1.2The technical content of this standard has been stable since 1993 without significant objection from its stakeholders. As there is limited technical support for the maintenance of this standard, changes since that date have been limited to items required to retain consistency with other ASTM D30 Committee standards, including editorial changes and incorporation of updated guidance on specimen preconditioning and environmental testing. The standard, therefore, should not be considered to include any significant changes in approach and practice since 1993. Future maintenance of the standard will only be in response to specific requests and performed only as technical support allows.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3.1Within the text the inch-pound units are shown in brackets.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
ASTM D 4255/D4255M : 2020 | Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method |
ASTM D 3171 : 1999 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM D 2584 : 2002 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM E 456 : 2002 | Standard Terminology for Relating to Quality and Statistics |
ASTM D 3878 : 2002 : REV A | Standard Terminology for Composite Materials |
ASTM E 456 : 2013 : REV A : R2022 | Standard Terminology Relating to Quality and Statistics |
ASTM E 1237 : 1993 : R1998 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 3878 : 2015 | Standard Terminology for Composite Materials |
ASTM D 2584 : 2008 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 3878 : 2019 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2000 | Standard Terminology Composite Materials |
ASTM D 2584 : 1994 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 3171 : 2011 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 6 : 2002 | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 2734 : 2016 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
ASTM E 122 : 2017 : R2022 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
ASTM E 122 : 2017 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
ASTM D 3878 : 2003 : REV A | Standard Terminology for Composite Materials |
ASTM D 2584 : 2011 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 1237 : 1993 : R2009 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 3878 : 2016 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2019 : REV A | Standard Terminology for Composite Materials |
ASTM D 3878 : 2020 : REV A | Standard Terminology for Composite Materials |
ASTM D 3878 : 1998 | Standard Terminology Composite Materials |
ASTM D 3171 : 2022 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3878 : 2018 | Standard Terminology for Composite Materials |
ASTM D 3171 : 2009 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 3878 : 2002 | Standard Terminology for Composite Materials |
ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM E 1237 : 1993 : R2003 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 2584 : 1968 | Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins |
ASTM D 3878 : 2004 | Standard Terminology for Composite Materials |
ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 1237 : 1993 : R2014 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 2734 : 1994 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 3878 : 2007 : R2013 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2020 : REDLINE | Standard Terminology for Composite Materials |
ASTM D 3878 : 2020 | Standard Terminology for Composite Materials |
ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 3878 : 2003 | Standard Terminology for Composite Materials |
ASTM E 6 : 2015 : EDT 4 : REDLINE | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM D 3878 : 2007 | Standard Terminology for Composite Materials |
ASTM D 2734 : 2009 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 3171 : 1999 : R2004 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3171 : 2015 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
ASTM D 3878 : 2004 : REV A | Standard Terminology for Composite Materials |
ASTM D 3171 : 2006 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3878 : 2001 | Standard Terminology Composite Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.