ASTM D 5587 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure
Hardcopy , PDF
23-07-2019
English
01-07-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.
| Committee |
D 13
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.
1.1.1The CRE-type tensile testing machine has become the preferred test apparatus for determining trapezoid tearing strength. It is recognized that some constant-rate-of-traverse-type (CRT) tensile testing machines continue to be used. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier. The conditions for use of the CRT-type tensile tester are included in Appendix X1.
1.2This test method applies to most fabrics including woven fabrics, air bag fabrics, blankets, napped fabrics, knitted fabrics, layered fabrics, pile, and nonwoven fabrics. The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. Instructions are provided for testing specimens with or without wetting.
1.3Tearing strength, as measured in this test method, requires that the tear be initiated before testing. The reported value obtained is not directly related to the force required to initiate or start a tear.
1.4Two calculations for trapezoid tearing strength are provided: the single-peak force and the average of five highest peak forces.
1.5The values stated in SI units are to be regarded as the standard. The values stated in inch-pound units may be approximate.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 1296 : 2008 : R2015 | Standard Guide for Evaluating Chemical Protective Clothing |
| ASTM F 2774 : 2009 : R2014 | Standard Practice for Manufacturing Quality Control of Consumer Trampoline Bed Material |
| ASTM D 1424 : 2009 : R2019 | Standard Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus |
| ASTM D 5446 : 2008 : R2019 | Standard Practice for Determining Physical Properties of Fabrics, Yarns, and Sewing Thread Used in Inflatable Restraints |
| ASTM C 1695 : 2019 | Standard Specification for Fabrication of Flexible Removable and Reusable Blanket Insulation for Hot Service |
| ASTM D 4850 : 2013 : R2017 : EDT 1 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
| ASTM F 2407 : 2006 : R2013 : EDT 1 | Standard Specification for Surgical Gowns Intended for Use in Healthcare Facilities |
| ASTM F 3352 : 2019 | Standard Specification for Isolation Gowns Intended for Use in Healthcare Facilities |
| ASTM F 1002 : 2015 | Standard Performance Specification for Protective Clothing and Materials for Use by Workers Exposed to Specific Molten Substances and Related Thermal Hazards |
| ASTM F 2704 : 2017 : REV A | Standard Specification for Air-Fed Protective Ensembles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.