
ASTM D 5963 : 2004 : R2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by

Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader)
Hardcopy , PDF
18-12-2019
English
15-09-2015
This test method covers the measurement of abrasion resistance of rubbers (vulcanized thermoset rubbers and thermoplastic elastomers) that are subject to abrasive/frictional wear in actual service.
Committee |
D 11
|
DocumentType |
Test Method
|
Pages |
9
|
ProductNote |
Reconfirmed 2015
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the measurement of abrasion resistance of rubbers (vulcanized thermoset rubbers and thermoplastic elastomers) that are subject to abrasive/frictional wear in actual service. The abrasion resistance is measured by moving a test piece across the surface of an abrasive sheet mounted to a revolving drum, and is expressed as volume loss in cubic millimetres or abrasion resistance index in percent. For volume loss, a smaller number indicates better abrasion resistance, while for the abrasion resistance index, a smaller number denotes poorer abrasion resistance.
1.2Test results obtained by this test method shall not be assumed to represent the wear behavior of rubber products experienced in actual service.
1.3The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 8115 : 2017 | Standard Test Method for Rubber Property—Abrasion Resistance (Multi-Directional Platform Abrader) |
ASTM D 378 : 2010 : R2016 | Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type |
ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 3182 : 2015 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 297 : 2015 : REDLINE | Standard Test Methods for Rubber Products—Chemical Analysis |
ISO 9298:2017 | Rubber compounding ingredients — Zinc oxide — Test methods |
ASTM D 1765 : 2005 : REV A : EDT 1 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 1765 : 2003 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 3182 : 2007 : R2012 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 4483 : 1999 | Standard Practice for Determining Precision for Test Method Standards in the Rubber and Carbon Black Industries |
ASTM D 1765 : 2004 : EDT 1 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 4483 : 2005 : REV A | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 1765 : 2017 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 1765 : 2014 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 3182 : 1989 : R2006 | Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 1765 : 2000 : REV A | Standard Classification System for Carbon Blacks Used in Rubber Products |
ISO 4649:2017 | Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device |
ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1765 : 2018 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 3182 : 1989 : R2001 : EDT 1 | Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 1765 : 2001 : EDT 1 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 1765 : 2004 : REV A | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1765 : 2001 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 1765 : 2016 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 1765 : 2005 : REV A | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 1765 : 2013 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 1765 : 2006 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 3182 : 2007 | Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ISO 7619:1997 | Rubber Determination of indentation hardness by means of pocket hardness meters |
ASTM D 3182 : 2016 : REDLINE | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 4483 : 2005 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ISO 2393:2014 | Rubber test mixes — Preparation, mixing and vulcanization — Equipment and procedures |
ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
ISO 5725:1986 | Precision of test methods Determination of repeatability and reproducibility for a standard test method by inter-laboratory tests |
ASTM D 1765 : 2010 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 3182 : 1989 : R2001 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 1765 : 2004 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 4483 : 2014 : REV A | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 4483 : 2014 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
DIN 53516:1987-06 | TESTING OF RUBBER AND ELASTOMERS; DETERMINATION OF ABRASION RESISTANCE |
ASTM D 4483 : 2018 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 4483 : 2005 : REV A : R2011 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 3182 : 1989 : R1994 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 4483 : 2014-02 | PRACTICE FOR EVALUATING PRECISION FOR TEST METHOD STANDARDS IN THE RUBBER AND CARBON BLACK MANUFACTURING INDUSTRIES |
ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 3182 : 2016 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1765 : 2005 | Standard Classification System for Carbon Blacks Used in Rubber Products |
ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
ISO 2781:2008 | Rubber, vulcanized or thermoplastic Determination of density |
ASTM D 3182 : 2015 : REV A | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.