ASTM D 6113 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
Hardcopy , PDF
17-05-2021
English
04-12-2016
Committee |
D 09
|
DocumentType |
Test Method
|
Pages |
21
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This is a fire-test-response standard.
1.2Several fire-test-response characteristics, including the time to sustained flaming, heat release rate, total heat released, effective heat of combustion, and specific extinction area; are measured or calculated by this test method at a constant radiant heating flux. For specific limitations see also 5.7 and Section 6.
1.3The tests are conducted by burning the electrical insulating materials contained in electrical or optical fiber cables when the cable test specimens, excluding accessories, are subjected to radiant heat.
1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability or regulatory limitations prior to use. For specific precautionary statements, see Section 7.
1.6This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.
1.7Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
ASTM E 2061 : 2020 | Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles |
ASTM E 2067 : 2020 | Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests |
ASTM D 5485 : 2016 | Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
ASTM E 2102 : 2017 | Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater |
ASTM E 2067 : 2015 | Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests |
ASTM E 1474 : 1996 : REV A | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 1354 : 2010 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 2058 : 2001 | Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM E 2058 : 2006 | Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM D 5537 : 2008 | Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM D 5537 : 2003 | Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1354 : 2002 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 2014 : EDT 1 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5537 : 1999 | Standard Test Method for Heat Release, Flame Spread and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM D 5424 : 2005 | Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1474 : 2014 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 2058 : 2019 | Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM D 1711 : 2002 | Standard Terminology Relating to Electrical Insulation |
ASTM E 1354 : 2004 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 1999 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5424 : 2018 | Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1474 : 2001 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 1354 : 2010 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1474 : 2020 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 1474 : 2004 : EDT 1 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 1354 : 2003 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5537 : 2014 | Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1354 : 2002 : REV D : EDT 1 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 1711 : 2011 | Standard Terminology Relating to Electrical Insulation |
ASTM E 1474 : 2002 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 5485 : 2016 | Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
ASTM E 1354 : 2008 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 2002 : REV D | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5537 : 2010 | Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1474 : 2007 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM D 1711 : 2011 : REV A | Standard Terminology Relating to Electrical Insulation |
ASTM D 5485 : 2010 | Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
ASTM E 2058 : 2002 | Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM D 1711 : 2013 | Standard Terminology Relating to Electrical Insulation |
ASTM E 2965 : 2015 | Standard Test Method for Determination of Low Levels Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 2965 : 2016 | Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 2009 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 2965 : 2016 : REV A | Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5485 : 2005 | Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
ASTM E 1474 : 2004 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 2058 : 2013 : REV A | Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM E 1354 : 2015 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 2058 : 2002 : REV A | Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM D 1711 : 1999 | Standard Terminology Relating to Electrical Insulation |
ASTM E 1354 : 2016 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5485 : 2009 | Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 1711 : 2014 : REV A | Standard Terminology Relating to Electrical Insulation |
ASTM E 1354 : 2016 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1474 : 2020 : REV A | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM D 5424 : 1999 | Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM D 1711 : 2015 | Standard Terminology Relating to Electrical Insulation |
ASTM E 1354 : 2017 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 1711 : 2014 | Standard Terminology Relating to Electrical Insulation |
ASTM E 1354 : 2002 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 5424 : 2014 | Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1354 : 2015 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 2011 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 2011 : REV B | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 2058 : 2000 | Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM E 2058 : 2009 | Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM D 5537 : 2018 | Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1354 : 2011 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM D 1711 : 2020 | Standard Terminology Relating to Electrical Insulation |
ASTM D 5485 : 1999 | Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
ASTM D 1711 : 2008 | Standard Terminology Relating to Electrical Insulation |
ASTM E 2965 : 2017 | Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1474 : 2010 | Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter |
ASTM D 5424 : 2010 | Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM D 5485 : 2011 | Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter |
ASTM E 2058 : 2003 | Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) |
ASTM E 1354 : 2004 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 2013 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
ASTM E 1354 : 2014 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.